GAC LSM200 Series Скачать руководство пользователя страница 1

Страница: 1 / 11

LSM200 Series Load Sharing Modules 6-2021-B1 PIB4100

LSM200 Series

Load Sharing Modules

INTRODUCTION

SPECIFICATIONS

PERFORMANCE

Load Sharing

Adjustable to within ± 2 % between sets

Operating Modes

Isochronous and main power control

Reverse Power Monitor Trip Point

Adjustable from -2 to -20 %

Reverse Power Delay

(Inverse Time Delay)

Adjustable from 0.5 to 15 s

Forward Power Monitor Trip Point

ON trip point adjustable from 20 - 100 %

OFF trip point adjustable from 0 - 80 %

Forward Power Delay

Adjustable from 0.4 to 30 s

Power Output Signal

0 to -1 V DC reverse power

0 to +6 V DC forward power

Forward and Reverse Power

Relay Contact Rating

Form C, 10 A 290 VA

Parallel Cable

Relay Contact Rating

Gold Clad, 1.25 A 60 VA MAX

ENviRONMENtAl

Operating Temperature

-40 to 185 °F [-40 to +85 °C]

Humidity

up to 95 %

All Surface Finishes

Fungus proof and corrosion resistance

COMPliANCE / StANDARDS

Agency

LSM201 - CE Approved

LSM201N - Non-CE approved

ROHs - Compliant

The LSM200 Series controllers provide Isochronous load sharing. These multifunction

load sharing and power control modules support GAC speed control units on generator

set applications requiring isochronous paralleling and for mains power control.

Engine generator sets with isochronous speed control units maintain the requested

speed very precisely. If synchronous generators are electrically paralleled to increase

the total generated power capability, a system to apportion the load is required.

Even the finest electric governors have minor frequency differences among units to be

paralleled, which would cause power variations. In this case, one generator set would

continuously increase the power it produces, while the other sets would decrease the

power they produce.

This condition eventually leads to motorizing one or more generator/ engines. The load

sharing system continuously adjusts the governor speed settings so that no average power difference exists The generators are

locked together through electrical synchronizing torques acting as a tightly connected gear drive. The line current measurements

are usually taken from current transformers in the equipment such as those used for ammeter circuits.

The LSM201 is available in a CE and non-CE version. Each supports:

•

24 V DC

•

Isochronous Load Sharing

•

Load Anticipation and Droop

•

Forward and Reverse Power Monitoring and Reset Capability

•

Power Monitor Adjustment Control

•

Generator Power Ramping and Control

POWER iNPUt \ OUtPUt

3 phase

AC Voltage signals

Two selectable ranges accommodate

100 - 500 V AC line-to-line

Isolated from battery (-) by 5000 V DC

Isolated from case by 1000 V DC

3 phase AC Line Currents

0-5 Amps with 1.25 VA requirement

Isolated from case by 1000 V DC

Connected to Speed Control Module

DC Supply

24 -32 V DC (Transient and Reverse

voltage protected). Battery (-) on all sets

must be connected together in common

Polarity

Negative ground case isolated.

Power Consumption

Battery Supply

160 ma

AC Phase Voltage Inputs

2.5 ma

External Power Meter

(Voltage Output)

10 ma MAX Current

PHYSiCAl

Dimensions

See Section 4, Wiring and Dimensions

Weight

1.2 lbf [0.56 kgf]

Mounting

Any Position

REliABilitY

Vibration

5 g, 20 - 500 Hz

Testing

100 % functional tested

Содержание LSM200 Series











Результаты поиска

Содержание LSM200 Series

Отзывы:

GAC LSM200 Series, Руководство пользователя, Страница: 1 / 11

Результаты поиска

Содержание LSM200 Series

Отзывы: