manualshive.com logo in svg

Future Electronics Microsemi Avalanche, Руководство пользователя

Поделиться
Скачать
Future Electronics Microsemi Avalanche Скачать руководство пользователя страница 12

 
 

 

12 

 

3

 

Installation and Setting 

This section provides information about the software and hardware settings required to run 
the pre-programmed demo design on the Avalanche Board. 

3.1

 

Software Settings 

Download and install the latest release of Microsemi Libero® SoC PolarFire software from the 
Microsemi website, and register for a free one-year Gold License to the Libero software. The 
Libero SoC PolarFire installer includes FlashPro5 drivers. For instructions about installing 
Libero SoC PolarFire and SoftConsole, see the Libero Software Installation and Licensing 
Guide. For instructions about how to download and install Microsemi DirectCores and driver 
firmware cores on the PC where Libero SoC is installed, see the Installing IP Cores and Drivers 
User’s Guide. 

3.2

 

Hardware Settings 

This section provides information about LEDs, test points and power supply structure on the 
Avalanche Board. 

3.2.1

 

Power Supply LEDs 

The following table lists the power supply LEDs on the Avalanche Board. 

LED 

Description 

LED1 

5.0 V rail 

LED2 

3.3V rail 

LED3 

5.0 V rail (USB) 

Table 2 - Power Supply LEDs 

3.2.2

 

Test Points 

The following test points available on the Avalanche Board: 

 

TP1, TP2: headers 

 

TP3 to TP18 

Refer to the schematic for more details. 

3.2.3

 

Power Sources 

The following table lists the key power supplies required for normal operation of the 
Avalanche Board. 

PolarFire Bank 

I/O Rail 

Voltage 

Bank 0, 1 

VDD15 

1.5 V 

Bank 2 

3P3V 

3.3 V 

Bank 3 

3P3V 

3.3 V 

Bank 4 

VDD25 

2.5 V 

Table 3 - I/O Voltage Rails 

 

 

Содержание Microsemi Avalanche































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды