Usage condition for conventional system
output (Ch2,3) on "High Speed mode"
CAUTION
"High Speed mode" accepts most types of
peripherals but only digital servos.
• Connecting analog servos to these outputs will cause
malfunction. If you notice a problem with whole stick lever
throw, please check the peripherals. Change the operation
mode to "Normal mode" if any malfunction occurs.
Applicable systems: FASST-2.4GHz 7ch or 8ch/10ch/Multi-ch system
Compliance Information Statement
(for U.S.A.)
This device, trade name Futaba Corporation of America, model
number R6202SBW, complies with part15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
The responsible party of this device compliance is:
FUTABA Corporation of America
2681 Wall Triana Hwy Huntsville, AL 35824, U.S.A.
Phone:1-256-461-9399 FAX:1-256-461-1059
E-mail: [email protected]
56%:6SHFLÀFDWLRQV
FASST-2.4GHz
(7ch/8ch/10ch/Multi-ch) system/
S.BUS
2 port
and 2 channels for conventional system/high-speed receiver
• Size: 0.89 x 1.47 x 0.37 in. (22.5 x 37.4 x 9.3 mm)
• Weight: 0.25 oz. (7.2g)
• Power requirement: 3.7V to 7.4V(Voltage range: 3.5 to 8.4V)
* When using the ESC's regulated output, be sure its capacity meets your
requirements.
* The Battery F/S voltage is set for 4-cell NiCd/NiMH battery. Battery F/S
function doesn't work properly when other type battery is used.
* The fail safe function can be set for each channel when on "Multi-ch" mode.
However, it differs according to the transmitter. When on "7ch" mode, the
fail safe function can be set for 3-channel only.
*
S.BUS
port: R6202SBW can be used up to 7 channels or less on the "7ch"
mode and 16 ch DG1/2 or less on the "8ch/10ch/Multi-ch" mode.
However, it differs according to the transmitter.
Power source usage precautions
We do not recommend using less than 4.0V power. If
you use a lower voltage source, please keep in mind the
following.
• Fail Safe function MUST be in "off" since the battery f/s will
disturb the normal operation.
• Please make sure that the full loaded condition of the ESC
and the servos won't disturb the receiver operation before
starting flight.
This is very important since the receiver will stop operation
when the supply voltage drops to less than 3.5V.
• Please be sure that the ESC or ser vos can operate
flawlessly under the lower voltage.
• The receiver battery can be connected with any connectors.
The power source voltage must not exceed the servo's
rating.
Antenna installation precaution
WARNING
Be sure that the two antennas are placed at 90
degrees to each other.
• Futaba's Dual Antenna Diversity, or DAD, then seamlessly
selects the best signal reception between these antennas to
ensure that there is no loss of signal.
Antenna installation for carbon fuse
WARNING
At least 30mm of the antenna tip must be fully
exposed.
• Please make sure that the exposed portion cannot slide
back into the fuselage under wind pressure or other forces
during your flying session.
Link/Mode switch
LED
R6202SBW
R6202SBW
FASST-2.4GHz (7ch/8ch/10ch/Multi-ch) System
S.BUS 2 Ports and 2 Channels for Conventional
System High-Speed Receiver
Thank you for purchasing a Futaba
R6202SBW
FASST-
2.4GHz
compatible receiver.
The
R6202SBW
has a two-port
S.BUS
system output and
conventional system channel (2, 3ch) outputs. It can also be
used with conventional system servos and
S.BUS
system-
compatible servos and gyros. With two
S.BUS
ports, it's easy
to connect your
S.BUS
equipment.
When the linking procedure is performed,
R6202SBW
recognizes the signal mode (
FASST-2.4GHz
7ch mode or
8ch/10ch/Multi-ch mode) automatically.
In addition, the operating mode (high-speed mode/normal
mode) can be selected.
1M23N17450
＜
The same signal
＞
(Connectors)
s
Channel 2 output for conventional system (2)
s#HANNELOUTPUTFORCONVENTIONALSYSTEM
/Battery terminal (B)
s3"530ORT3"53
s3"530ORT3"53