Applicable systems: Futaba T-FHSS Air 2.4GHz system
LED Indication
LED
Status
Solid
Receiving signals
1 time blink
Waiting for link
2 times blink
No signal reception
2 times blink
(Every 4 seconds)
Unrecoverable error (Memory, etc.)
Antenna installation precaution
Do not cut or bundle the receiver antenna wire.
Do not bend the coaxial cable. It causes damage.
The antenna should not be pulled.
Keep the antenna as far away from the motor, ESC
and other noise sources as you possibly can.
Do not touch the antenna to metal, carbon, or other
conductive material.
Be sure that the two antennas are placed at 90 de-
grees to each other.
• The R3004SB has two antennas. In order to maximize signal recep-
tion and promote safe modeling Futaba has adopted a diversity an-
tenna system. This allows the receiver to obtain RF signals on both
antennas and fly problem-free.
Antenna installation for carbon fuse
WARNING
The antenna portion of 30mm tip must be fully ex-
posed.
• Please make sure that the exposed portion won't slide back in the
fuse due to wind pressure or other force during the flight session.
Usage precaution
• Futaba T-FHSS Air system does not work with current Futaba
FASST/FASSTest/S-FHSS/T-FHSS Car system. Futaba FASST/
FASSTest/S-FHSS/T-FHSS Car system and T-FHSS Air system
are not compatible to each other.
WARNING
Wrap the receiver with something soft, such as foam
rubber, to avoid vibration. Moreover, the receiver must
not get wet.
Do not short-circuit the connectors.
Do not expose the receiver to high temperatures.
• The shrink cover could become distorted.
Do not break the tube.
• Could cause a short circuit.
When inserting and removing a connector, hold the
receiver tightly.
• Be careful so that a tube doesn't come off.
Please refer the table below for
LED status vs receiver's condition.
1M23N34104
R3004SB
Antenna
S.BUS2 Port
CH1-CH4 output
conventional system Port
LED
S.BUS2 equipment
Direction of the connectors
90˚
Antenna installation
R3004SB
T-FHSS Air 2.4GHz System
S.BUS2 port and 4 channels for conventional system
Small size, Light weight Receiver
Thank you for purchasing a Futaba
R3004SB
T-FHSS Air-2.4GHz
compatible receiver.
The
R3004SB
receiver features bi-
directional communication with a
T-FHSS Air-2.4GHz
Futaba transmitter using the
S.BUS2
port. Using the
S.BUS2
port an
impressive array of telemetry sensors may be utilized.
The receiver power
supply can
be
connected to any port.
Receiver
Tags are downwards
Upper Side (Label)
Declaration of Conformity (for EU)
Hereby, Futaba Corporation declares that the radio equipment type is R3004SB in compli-
ance with Directive 2014/53/EU. The full text of the EU declaration of conformity is avail-
able at the following internet address:
http://www.rc.futaba.co.jp/english/dl/declarations.html
Compliance Information Statement (for Canada)
This device complies with Industry Canada license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired
operation of the device. This equipment complies with IC radiation exposure limits set
forth for an uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
French: Cet appareil radio est conforme au CNR-210 d’Industrie Canada. L’utilisation
de ce dispositifest autorisée seulement aux deux conditions suivantes : (1) il ne doit
pas produire de brouillage, et (2) l’utilisateur du dispositif doit être prêt à accepter tout
brouillage radioélectrique reçu, même sice brouillage est susceptible de compromettre le
fonctionnement du dispositif. Cet équipement est conforme aux limites d’exposition aux
rayonnements IC établies pour un environnement non contrôlé.
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour
un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un mini-
mum de 20 cm de distance entre la source de rayonnement et votre corps.
Compliance Information Statement (for U.S.A.)
This device, trade name Futaba Corporation, model number R3004SB, complies with
part15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
CAUTION: To assure continued FCC compliance
1. Any changes or modifications not expressly approved by the grantee of this device
could void the user's authority to operate the equipment.
2. This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between
the radiator & your body.
The responsible party of this device compliance is:
Futaba Service Center
3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.
TEL (217)398-8970 or E-mail: [email protected] (Support)
