manualshive.com logo in svg

Furuno NAVpilot 711C, Руководство оператора, Страница: 47 / 176

Поделиться
Скачать
Furuno NAVpilot 711C Скачать руководство пользователя страница 47

2.  STEERING MODES

2-23

2.7.2

How to adjust the SABIKI mode response

When vessel direction adjustment during the SABIKI mode is problematic, use the fol-
lowing procedure to adjust the response level for the SABIKI mode.

1. Push the 

 key to show the turn menu.

2. Select the SABIKI mode icon, then push the 

 key. The [SABIKI Option] window 

is displayed.

Note: 

The [Rudder Drive Level] menu option 

is not available when using Fantum 
Feedback

™

The [SABIKI Option] window may also be 
displayed in the following manners:
•  While the SABIKI mode is active, press 

and hold the 

 key.

•  From the menu: [Other Menu] 

o

 [SABIKI 

Option].

3. Select the current setting value at [Response at SABIKI Mode], then push the 

Course control

 knob.

4. Turn the 

Course control

 knob to adjust the response setting.

•  Where the SABIKI mode over-corrects the direction: Increase the response 

level. If the direction is over-corrected with this setting, reduce reverse throttle.

•  Where the SABIKI mode under-corrects direction: Reduce the response level. 

If the direction is under-corrected with this setting, increase reverse throttle.

5. To apply the response settings, push the 

Course control

 knob.

6. Rotate the 

Course control

 knob to select [Run], then push the knob.

2.7.3

Rudder drive settings for the SABIKI mode

During the SABIKI mode, it is possible to adjust the rudder drive settings. A high 
setting gives a larger rudder turn.

1. Push the 

 key to show the turn menu.

2. Select the SABIKI mode icon, then push the 

 key. The [SABIKI Option] window 

is displayed.
The [SABIKI Option] window may also be displayed in the following manners:

•  While the SABIKI mode is active, press and hold the 

 key.

•  From the menu: [Other Menu] 

o

 [SABIKI Option].

3. Select the current setting value at [Rudder Drive Level], then push the 

Course 

control

 knob.

Note: 

The [Rudder Drive Level] menu option is not available when using Fantum 

Feedback

™

.

4. Turn the 

Course control

 knob to adjust the drive level setting.

5. To apply the response settings, push the 

Course control

 knob.

6. Rotate the 

Course control

 knob to select [Run], then push the knob.

SABIKI Option

Run

Response at SABIKI Mode:
Rudder Drive Level: 6

1

Содержание NAVpilot 711C

















































































































































































Отзывы:

Нет отзывов