Furuno NAVpilot 711C Скачать руководство пользователя страница 17

Страница: 17 / 176

1. OPERATIONAL OVERVIEW

1-3

1.3

How to Adjust the Brilliance

1. Long press the

key to open the menu.

2. Rotate the

Course control

knob to select [Brilliance] then push the knob.

The brilliance adjust window appears. The window closes automatically when
there is no operation for a while.

3. Rotate the

Course control

knob to adjust the brilliance.

The higher the value, the brighter the display.

4. Push the

Course control

knob to close the window.

5. Push the

key to close the menu.

1.4

How to Set the Display Color

1. Long press the

key to open the menu.

2. Rotate the

Course control

knob to select the current setting for [Display Color]

then push the knob.

3. Rotate the

Course control

knob to select the display color.

[White]: White-themed display
[Black]: Black-themed display

4. Push the

key to close the menu.

Message

Display Color : White

Sensor In Use

Brilliance

Advanced AUTO: ON

Net Towing AUTO : OFF

Message

Display Color : White

Sensor In Use

Brilliance

Advanced AUTO: ON

Net Towing AUTO : OFF

Example: [Display Color] = [White]

Example: [Display Color] = [Black]

Содержание NAVpilot 711C

















































































































































































Результаты поиска

Содержание NAVpilot 711C

Отзывы:

Furuno NAVpilot 711C, Руководство оператора, Страница: 17 / 176

Результаты поиска

Содержание NAVpilot 711C

Отзывы: