Furuno NAVpilot 711C Скачать руководство пользователя страница 113 | Manualshive

Страница: 113 / 176

Furuno NAVpilot 711C Скачать руководство пользователя страница 113

7-1

7.

INITIAL SETTINGS

This chapter shows you how to enter initial settings, on the [Installation Menu] window.
The menu contains some items that may not apply to your system. Minimally, the set-
tings on the following menus must be done:

• [Ship’s Characteristics] menu
• [Dockside Setup] menu

Note:

The [Dockside Setup] menu is not shown when [Boat Type] is set to [EVCS

Boat].

7.1

How to Select Language and Units, Open the In-
stallation Menu Window

1. Press the

key to turn on the power.

The first time the system is powered, the language selection window appears.

2. Rotate the

Course control

knob to select a language then push the knob.

3. Press the

key to open the [Units Setup] menu.

The units on the [Units Setup] menu are set according to the language selected.

4. If you want to change the units, do as follows. If not, go to the next step.

1) Rotate

the

Course control

knob to select the current setting to change then

push the knob.

2) Rotate

the

Course control

knob to select a unit then push the knob.

㪜㫅㪾㫃㫀㫊㪿㩷㩿㪬㪪㪘㪀

㪜㫅㪾㫃㫀㫊㪿

㪝㫉㪸㫅㪺㪸㫀㫊

㪜㫊㫇㪸㫅㫆㫃

㪧㫆㫉㫋㫌㪾㫌㪼㫊

㪛㪼㫌㫋㫊㪺㪿㪼

Speed Unit:

kn

Range Unit: NM

Wind Speed Unit: kn

Depth Unit: ft

Water Temp Unit:

°

F

Prev Next

Units Setup

«
...
111
112
113
114
115
...
»

Содержание NAVpilot 711C

















































































































































































Отзывы:

Нет отзывов