Furuno FELCOM250 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 69

Furuno FELCOM250 Скачать руководство пользователя страница 35

3-1

3.

SETTING AFTER INSTALLATION

This chapter shows how to enter basic settings, done by the installation technician.
For the network setting, request to an administrator of the ship network. (Refer to the
Operator's Manual for details.)

The SIM card is required to communicate via a satellite, but not required for the fol-
lowing system settings. "(SIM): No SIM" appears in the Web software screen. Disre-
gard the warning.

3.1

Preparation for Setting

1. Connect the PC to the Communication Unit with a LAN cable.
2. Turn on the PC.

Note:

Set the Internet Protocol (TCP/IP) Properties of PC to "Obtain an IP ad-

dress automatically". If you set the PC IP address manually, set it according to the
IP address of the Communication Unit (default 192.168.1.1).

3. Turn on the Communication Unit.

The initialization begins. During this time, the PC cannot access the Communica-
tion Unit.

4. When all STATUS LEDs are lit, activate the Web browser.
5. Enter “192.168.1.1” in the address bar and press the

Enter

key.

The main menu of the Web software opens.

Note:

You can add the main menu of the Web software to “Favorite” or “Book-

mark” for easy access.

SIM CARD INSIDE

POWER OFF BEFORE INSERTING

OR REMOVING SIM

―

○

POWER

○

I

POWER

1

TX

2

3

4

STATUS

Inmarsat FleetBroadband

READY

Power switch

Communication unit

«
...
33
34
35
36
37
...
»

Содержание FELCOM250






































































Отзывы:

Нет отзывов