manualshive.com logo in svg

Furuno FCV-38, Руководство пользователя

Поделиться
Скачать
Furuno FCV-38 Скачать руководство пользователя страница 90

4.  ADVANCED SETTINGS

4-8

4.6.2

Calibration menu

The external fish finder settings can be calibrated from the [Calibration] section of the 
[External Echo Sounder] menu. To calibrate settings for the FCV-38, see 
section 4.7.5.

Menu item

Description

[Zero Line Rejector]

Turns the zero line (transmission line) on or off. When 
turned [On], the transmission line disappears, which al-
lows you to see fish echoes near the surface clearly. The 
width of the transmission line changes with transducer 
used and installation characteristics.

[Zero Line Area]

Adjusts the transmission line so that the transmission line 
disappears when the [Zero Line Rejector] is turned on. 
For a long tail, increase the value. If the transmission line 
does not disappear, lower the TX power.

[Gain ADJ (HF)], [Gain ADJ 
(LF)]

Stabilizes the gain, allowing for a clear picture when the 
gain is set at a very low/high setting. This function is also 
helpful in that it balances the gain between HF and LF im-
ages.

[TD fore-aft]

Sets the fore-aft position of the external Fish Finder’s 
transducer. This setting is done at installation, do not 
change this setting.

[TD port-stbd]

Sets the port-stbd position of the external Fish Finder’s 
transducer. This setting is done at installation, do not 
change this setting.

[ANT TD height]

Sets the height of the Satellite Compass

™

 antenna above 

the waterline. This setting is done at installation, do not 
change this setting.

FCV-38[ver 0252473-xx.xx]

Содержание FCV-38

























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды