manualshive.com logo in svg

Furuno FCV-38, Руководство пользователя

Поделиться
Скачать
Furuno FCV-38 Скачать руководство пользователя страница 53

1.  OPERATION

1-41

1

1.26

How to Erase Weak Echoes

Sediment in the water or reflections from plankton may be painted on the display in 
low intensity tones, as shown in the illustration below. You can remove these unwant-
ed echoes with the color erase feature.

1.26.1

How to erase weak echoes for the FCV-38 and external echo 
sounders

Where [External Fish Finder Window] is set to [Off] at installation, this setting is ap-
plied to the external fish finder also.

1. Select the [Advanced Settings] icon (

) from the InstantAccess bar™ to show 

the [Advanced Settings] menu.

2. Select the [Advanced Settings] icon (

) from the [Advanced Settings] menu. The 

[Advanced Settings] window appears.

3. The [Sounder] menu item is already selected and the [Sounder] menu appears on 

the right-side of the window. Select [Color Erase] from the [Sounder] menu.

4. Adjust the [Color Erase] setting until the picture shows minimal reflections. As the 

setting increases, reflections are removed in order, from weakest to strongest.

5. Select [Apply] to save the current changes and change or adjust other settings.

Select [OK] to save the current changes and close the menu window.
Select [Cancel] to abort all changes and close the menu window.

Weak echoes

Color erase setting

FCV-38[ver 0252473-xx.xx]

Содержание FCV-38

























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды