Furuno FCV-38 Скачать руководство пользователя страница 101

Страница: 101 / 152

4. ADVANCED SETTINGS

4-19

4.7.6

Calibration Settings menu

The [Calibration Settings] menu calibrates the FCV-38 system. For further details see
section 5.4.

4.7.7

Stabilization menu

The [Stabilization] section of the [System] menu mainly compensates for heaving. See
the Notes below to enable use of this function.

Note 1:

This function requires connection to a Satellite Compass

™

. If data from the

compass is lost or interrupted, the function is disabled.

Note 2:

To use stabilization, set output data on the Satellite Compass

™

as shown be-

low. See the operator’s manual for the Satellite Compass

™

•  Output sentence: ATT (GPatt), HVE (GPhve)
•  Baud rate: 38,400 bps
•  Output interval: 25 ms or less
•  Version (SC-50/110 only): IEC ED1

Note 3:

This function is unavailable if [KP Input] is set to [On] at installation.

Menu item

Description

[Stabilization]

Turns heaving compensation on or off. Turn it on when seas are rough, to
get stable echoes, regardless of sea conditions. When turned on, the sta-
bilization icon (

) appears in the [Picture Advance] section of the

header.

Note:

Where data from the Satellite Compass

™

is interrupted or lost, the

stabilization icon is overlaid with a cross to indicate that it is not in use.
When data from the Satellite Compass

™

is received again, the cross is re-

moved.

FCV-38[ver 0252473-xx.xx]

Motion Sensor

Содержание FCV-38

























































































































































Результаты поиска

Содержание FCV-38

Отзывы:

Бренды по названию

Популярные бренды

Furuno FCV-38, Руководство пользователя

Результаты поиска

Содержание FCV-38

Отзывы:

Бренды по названию

Популярные бренды