Furuno DS-80 Скачать руководство пользователя страница 38

Страница: 38 / 84

7. Select DATA OUTPUT and press the [ENT] key.

8. Press



to select ON and press the [ENT] key.

9. Press the [DISP] key.

10. Confirm the value displayed is the same as it entered at step 5.

Confirm the same as speed is shown on external equipment (radar, GPS, etc.).

11. Select OFF at DATA OUTPUT, and press the [ENTER] key.

3.4

Setting of Maximum Speed Range

Change the maximum range of the connected analog display by setting ofDIP switch S2 in the
distribution box.

Maximum speed

20 kn

30 kn

40 kn

S2 #1:

Others: OFF

All: OFF

#2: ON
Others: OFF

JPW Board
(65P6010)

Distribution box DS-801,
inside view

S2
(Default setting: all OFF)

Distribution box, cover removed

3.5 Ship's

Speed

Adjustments

Adjusts the speed error using the test sheet on page AP-3 recorded.

1. Press the [MENU] key.

2. Select SYSTEM MENU, and press the [ENT] key.

3. Select SPEED OFFSET, and press the [ENT] key.

4. Use the cursor pad to enter the digit.

5. Press the [ENT] key.

6. Press the [MENU] key.

For detail, see page AP-1.

Содержание DS-80





















































































Результаты поиска

Содержание DS-80

Отзывы:

Furuno DS-80, Руководство по установке, Страница: 38 / 84

Результаты поиска

Содержание DS-80

Отзывы: