manualshive.com logo in svg

Furuno DS-80, Руководство по установке, Страница: 37 / 84

Поделиться
Скачать
Furuno DS-80 Скачать руководство пользователя страница 37

 

31  

Setting of language 

The display language can be selected for English or Japanese. 

1.  Press the [MENU] key to display the main menu. 

2.  Select SYSTEM MENU 2 and press the [ENT] key to display the system menu 2. 

3.  Select LANG. And press the [ENT] key to display the language pop-up menu. 

E N G L I S H

 

Language pop-up window 

4.  Select ENGLISH or JAPANESE with 

 or 

 key. 

5.  Press the [ENT] key. 

6.  Press the [MENU] key twice to close the menu. 

3.3 Checking 

the 

Interconnection 

After installation the equipment do the following to confirm if the doppler speed signal is being 
output correctly. 

1.  Press the [MENU] key to display the main menu. 

2.  Select SIM, and press the [ENT] key to display the sim menu. 

SIM 

+10.0 kn

SPEED

DATA DISPLAY             OFF

ENT

SET

 

SIM MODE menu 

3. Select 

SPEED. 

4.  Press the [ENT] key. 

5.  Use the cursor pad to enter the speed value desired. 



: Change value, +/- 



: Change digit 

6.  Press the [ENT] key. 

Содержание DS-80





















































































Отзывы:

Нет отзывов