manualshive.com logo in svg

Furuno DS-80, Руководство по установке

Поделиться
Скачать
Furuno DS-80 Скачать руководство пользователя страница 35

 

29  

3. SYSTEM 

SETTINGS 

3.1 Transducer 

Adjustment

 

Transducer mounted error, which causes incorrect speed value, can be compensated through 
the menu (Range: -45

°

to +45

°

). 

1.  Press the [MENU] key to display the main menu. 

DISTANCE RUN DISPLAY

DEMO 

SYSTEM MENU
SYSTEM

 MENU 2

MENU

 

Main menu 

2.  Select SYSTEM MENU and press the [ENT] key to display the system menu. 

SYSTEM MENU

SHIP SPD AVG
SPEED OFFSET
TRACK DEPTH
XDR OFFSET
SPD DATA SELECT

1 5   S E C

-   0 . 0 %

2 . 0 m

- 0 0  

DOPPLER

ENT : SET

 

System menu 

3.  Select XDR OFFSET and press the [ENT] key. 

4. Press 

or

 to select the digit or sign (+ or -) you want to change; press 

 or 

 to select 

the digit and +/-. For example, when there is +5

°

error, enter “+05”. 

5.  Press the [ENT] key. 

6.  Press the [MENU] key twice to close the menu. 

Correction 

value (0)

Correction 

value (+

α

)

α

α

Correction 

value (-

α

)

 

Содержание DS-80





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды