manualshive.com logo in svg

Furuno DS-80, Руководство по установке, Страница: 33 / 84

Поделиться
Скачать
Furuno DS-80 Скачать руководство пользователя страница 33

 

27  

2.4 

Wiring of Terminal Box 

Fix the cables with the cable tie at the fixing plate. All cables except the power cable should be 
fixed by the clamp with the armor. 

Fabrication of TTYCY-2S   
(for display unit and digital indicator/distance indicator) 

Within 120 mm

20

15

Anticorrosive 
sheath

1

2

Remove the shield between the fixing plate
and terminal box.

Armor

Shield

FV2-M4

 

Fabrication of cable TTYCY-3S 

TTYCYS-1 

Cut vinyl sheath between armor and shield, and wind shield around armor and then lay cable so 
armor is in the cable clamp. 

FV2-M4

Armor

within 120

Anticorrosive
Sheath

Wind the shield.

 

20S0251 (for display unit, digital indicator/distance indicator) 

•

 

Locate the fuse of the cable inside the terminal box.   

•

 

Tape the drain wire, and fix the earth terminal in the terminal box.   

•

 

Outer sheath should be fixed in the cable clamp. 

65S1231 (for display unit, digital indicator/distance indicator) 

Strip the outer sheath by 120 mm, and fasten it by the clamp. Attach the climp-on lug FV0.5-4 to 
each core. 

Содержание DS-80





















































































Отзывы:

Нет отзывов