background image

Questions?  Please Contact Your Local Manufacturer’s Representative

SECTION 2

 

VSRT-IOM-2022-0728

 

INSTALLATION

2-45

3.  Install the top fitting (the fitting without the drain port) 

into the upper fitting on the water bottle using service 
rated sealant. Wrench tighten the fitting until it is snug 
and the glass outlet is pointing at about 5 o’clock (about 
1/8 turn from its final downward vertical position).

4.  Install the bottom fitting (the fitting with the drain port) 

into the lower fitting on the water bottle. Wrench tighten 
the fitting until it is snug and the glass outlet is pointing 
directly upward.

5.  Verify that the top and bottom fittings are threaded 

into the water bottle tappings the same amount 
(horizontally).

6.  Remove the glass packing nut, friction washer and glass 

packing from the fittings and place them in the same 
order on either end of the water gauge glass. Push both 
packings about 1in (25.4 mm) from the end of the water 
gauge glass.

7.  Gently insert one end of the water gauge glass into the 

top gauge fitting. Keeping the glass inside the fitting, 
gently rotate the top fitting clockwise until it is vertically 
aligned with the bottom fitting. 

It is crucial that the 

gauge glass valves are aligned both vertically and 
horizontally. If not aligned, they may leak.

8.  Insert the gauge glass into the bottom fitting until it 

bottoms out, and then gently raise glass about 1/16 in 
(1.6 mm). Do not allow glass to remain in contact with 
any metal surface. 

9.  Carefully slide the bottom glass packing down until 

the glass packing is touching the lower gauge fitting. 
Carefully slide the top glass packing up until the glass 
packing is touching the upper gauge fitting.

10.  Hand tighten both glass packing nuts, then tighten ½ 

turn more by wrench. Do not overtighten. If any leakage 
occurs, tighten the packing nut slightly, no more than a 
¼ turn at a time, until the leak stops.

11.  When provided, install the protective guard over the 

gauge glass assembly.

12.   The gauge glass valves are fitted with ball checks. Make 

sure that the valves are fully open to ensure that the ball 
check will function properly in the event that the gauge 
glass breaks.

13.  Install drain piping from water bottle and lower water 

gauge glass fitting to the boiler blo

w off piping.

Stack & Flue Connections

Adhere to the following for stack and flue connections:

1.  An appropriately-sized stack should be connected to 

the flue gas outlet at the boiler. The proper flue size 
and draft control is most important for proper burner 
operation. The flue must be as large or larger than the 
outlet on the vessel. Avoid long flue piping and too 
many elbows by placing the equipment as close as 
possible to the chimney.

2.  The stack should rise continuously to the connection 

at the chimney and should contain no more than two 
bends at 45 degree angles or less. If required, as a result 
of space limitations, one 90 degree elbow (or tee) can be 
fitted at the back of the vessel.

3.  Any alternative stack arrangement must supply the 

following draft:

 

ƒ

VSRT must supply a draft condition of -0.25” w.c.  
to + 1.50” w.c draft at the boiler. 

 

ƒ

Positive pressure draft requires a CAT 3 stack.

4.  The run in the total distance of stack ducting, as 

measured in a straight line from the outlet of the boiler 
to the outlet of the stack, should not exceed 25% of 
the rise.   With the exception of the duct run previously 
described, horizontal sections of ducting must be 
avoided and should not exceed four feet total.  See 

Figures 28-29.

5.  The stack and chimney material shall comply with all 

applicable codes.

6.  Adequate provision must be made for the support of 

the weight of the chimney and stack to avoid having 
a load imparted to the outlet connection of the 
equipment.

7.  The installation of a draft regulator by the client/

contractor is recommended at all installations.  This will 
help to maintain the required draft.  The placement of 
the draft regulator should be as shown in  

Figures 28-29.

Содержание VSRT Series























































































































Отзывы: