FULTON FB-A 10 Скачать руководство пользователя страница 97

Страница: 97 / 102

Standard Warranty for Fulton Boilers

Warranty Valid for Models ICS, ICX, ICW, ICXW, VMP, VMPW, FB-A, FB-F, FB-L, FB-S, FB-W

Five (5) Year (60 Months) Material and Workmanship Warranty

The pressure vessel is covered against defective material or workmanship for a period of five (5)

years from the date of shipment from the factory. Fulton will repair or replace F.O.B. factory any

part of the equipment, as defined above, provided this equipment has been installed, operated

and maintained by the buyer in accordance with approved practices and recommendations made

by Fulton. The commissioning agency must also successfully complete and return the equipment

Installation and Operation Checklists to Fulton’s Quality Assurance department. This warranty

covers any failure caused defective material or workmanship; however, waterside corrosion or

scaling is not covered. Therefore, it is imperative that the boiler water management and chemistry

be maintained as outlined in the Installation and Operation Manual.

Parts Warranty

Fulton will repair or replace F.O.B. factory any part of the equipment of our manufacture that is

found to be defective in workmanship or material within one (1) year of shipment from the factory

provided this equipment has been installed, operated and maintained by the buyer in accordance

with approved practices and recommendations made by both Fulton and the component

manufacturers and the commissioning agency has successfully completed and returned the

equipment Installation and Operation Checklists to Fulton’s Quality Assurance department.

General

Fulton shall be notified in writing as soon as any defect becomes apparent. This warranty does

not include freight, handling or labor charges of any kind.

These warranties are contingent upon the proper sizing, installation, operation and maintenance

of the boiler and peripheral components and equipment. Warranties valid only if installed,

operated, and maintained as outlined in the Fulton Installation and Operation Manual.

No Sales Manager or other representative of Fulton other than the Quality Manager or an officer

of the company has warranty authority. Fulton will not pay any charges unless they were pre-

approved, in writing, by the Fulton Quality Manager.

This warranty is exclusive and in lieu of all other warranties, expressed or implied, including but

not limited to the implied warranties of merchantability and fitness for a particular purpose. Fulton

shall in no event be liable for any consequential or incidental damages arising in any way,

including but not limited to any loss of profits or business, even if the Fulton Companies has been

advised of the possibility of such damages. Fulton’s liability shall never exceed the amount paid

for the original equipment found to be defective.

To activate the warranty for this product, the appropriate commissioning sheets must be

completed and returned to the Fulton Quality Assurance department for review and approval.

9/9/09

88-G 1/01

Содержание FB-A 10







































































































Результаты поиска

Содержание FB-A 10

Отзывы:

Похожие инструкции для FB-A 10

Бренды по названию

Популярные бренды

FULTON FB-A 10, Инструкция по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание FB-A 10

Отзывы:

Похожие инструкции для FB-A 10

Бренды по названию

Популярные бренды