frequency
interference,
in
which
case
the
user
will
be
required
to
correct
the
interference
at
the
user's
own
expense.
This
equipment
has
been
tested
and
found
to
comply
with
the
limits
for
a
Class
A
digital
device,
pursuant
to
Part
15
of
the
FCC
rules,
and
meets
all
requirements
of
the
Canadian
Interference-
Causing
Equipment
Standard
(ICES-003)
for
digital
apparatus.
These
regulations
are
designed
to
provide
reasonable
protection
against
radio
interference
when
the
equipment
is
operated
in
a
residential
installation.
This
product
generates,
uses,
and
can
radiate
radio
frequency
energy
and,
if
not
installed
and
used
in
strict
accordance
with
the
instructions,
may
cause
harmful
interference
to
radio
communications.
However,
there
is
no
warranty
that
interference
will
not
occur
in
the
conditions
at
a
particular
installation.
If
the
product
causes
harmful
interference
to
radio
or
television
reception
(which
can
be
confirmed
by
switching
the
equipment
on
and
off),
the
user
is
encouraged
to
try
to
correct
the
interference
by
one
or
more
of
the
following
measures:
-
Reorient
or
relocate
the
receiving
antenna.
-
Increase
the
distance
between
the
equipment
and
the
receiver.
-
Connect
the
equipment
into
an
outlet
on
a
circuit
separate
from
that
connected
to
the
receiver.
-
Consult
a
reseller
or
experienced
radio/TV
technician
for
support.
Fujitsu
is
not
responsible
for
any
radio
or
television
interference
caused
by
unauthorized
modification
of
this
equipment
or
the
substitution
or
attachment
of
connecting
cables
and
equipment
other
than
those
specified
by
Fujitsu.
The
user
shall
be
responsible
for
correcting
the
interference
caused
by
such
unauthorized
modification,
substitution,
or
attachment.
The
use
of
shielded
I/O
cables
is
required
when
connecting
the
equipment
to
any
optional
peripheral
or
host
device.
Failure
to
use
shielded
I/O
cables
may
violate
FCC
and
ICES
regulations.
2.6.2
FCC
Class
A
Declaration
of
Conformity
The
device
may
be
marked
with
an
FCC
declaration,
which
would
apply
to
the
equipment
covered
in
this
document
unless
otherwise
specified
herein.
The
declaration
for
other
products
will
appear
in
the
accompanying
documentation.
2.7
Environmental
Protection
Environmentally-Friendly
Product
Design
and
Development
This
product
has
been
designed
in
accordance
with
the
Fujitsu
standard
for
"environmentally
friendly
product
design
and
development."
This
means
that
key
factors
such
as
durability,
selection
and
labeling
of
materials,
emissions,
packaging,
and
ease
of
dismantling
and
recycling
have
been
taken
into
account.
This
saves
resources
and
thus
reduces
the
harm
done
to
the
environment.
Energy-Saving
Information
Devices
that
do
not
need
to
be
constantly
switched
on
should
be
switched
off
until
they
are
needed
as
well
as
during
long
breaks
and
after
completion
of
work.
Chapter
2
Important
Information
C120-0090-04EN
2.7
Environmental
Protection
7
Содержание Supercomputer PRIMEHPC FX700
Страница 105: ......
