Fujitsu SPARC Enterprise T5440 Server Скачать руководство пользователя страница 11

Страница: 11 / 92

C H A P T E R

New Information About the SPARC
Enterprise T5440 Server

This chapter describes new information about the SPARC Enterprise T5440 server
that was not documented in the previous edition of the

SPARC Enterprise T5440

Server Product Notes

Information that was documented in the previous edition of this document is
provided in the following locations:

■

Chapter 2

provides important information about what software is preinstalled on

your server, how to obtain support, and how to determine system configuration.

■

Chapter 3

provides important information about hardware, software, and

firmware issue and available workarounds.

■

Chapter 4

provides updates to existing system documentation.

■

Appendix A

describes fixed technical issues.

Description

Links

Important new information about the T5440
server

“Important New Information About the
SPARC Enterprise T5440 Server” on page 2

Issues that were identified after the
previous edition was published

“New Information About Known Issues” on
page 3

Содержание SPARC Enterprise T5440 Server





























































































Результаты поиска

Содержание SPARC Enterprise T5440 Server

Отзывы:

Похожие инструкции для SPARC Enterprise T5440 Server

Бренды по названию

Популярные бренды

Fujitsu SPARC Enterprise T5440 Server, Руководство пользователя

Результаты поиска

Содержание SPARC Enterprise T5440 Server

Отзывы:

Похожие инструкции для SPARC Enterprise T5440 Server

Бренды по названию

Популярные бренды