Fujitsu SPARC Enterprise M4000 Скачать руководство пользователя страница 23

Страница: 23 / 444

Intro(8)

System Administration

NAME

Intro - eXtended System Control Facility (XSCF) man pages

DESCRIPTION

This manual contains XSCF man pages.

LIST OF

COMMANDS

The following commands are supported:

Intro

intro

eXtended System Control Facility (XSCF) man pages

addboard

configure an eXtended System Board(XSB) into the domain
configuration or assigns it to the domain configuration

addcodlicense

add a Capacity on Demand (COD) right-to-use (RTU)
license key to the COD license database

addfru

add a Field Replaceable Unit (FRU)

adduser

create an XSCF user account

applynetwork

reset XSCF to reflect information that has been set for the
XSCF network

cfgdevice

connect a DVD/TAPE drive to the port, disconnect it from
the port, or display the status of the drive

clockboard

set or display the clock control unit used at system startup

console

connect to a domain console

deleteboard

disconnect an eXtended System Board (XSB) from the
domain configuration

deletecodlicense

remove a Capacity on Demand (COD) right-to-use (RTU)
license key from the COD license database

deletefru

delete a Field Replaceable Unit (FRU)

deleteuser

delete an XSCF user account

disableuser

disable an XSCF user account

enableuser

enable an XSCF user account

exit

exit the XSCF shell

flashupdate

update the firmware

fmadm

fault management configuration tool

fmdump

view fault management logs

fmstat

report fault management module statistics

getflashimage

download a firmware image file

ioxadm

manage External I/O Expansion Units

Содержание SPARC Enterprise M4000





























































































































































































































































































































































































































































Результаты поиска

Содержание SPARC Enterprise M4000

Отзывы:

Fujitsu SPARC Enterprise M4000, Справочное руководство, Страница: 23 / 444

Результаты поиска

Содержание SPARC Enterprise M4000

Отзывы: