Fujitsu PRIMERGY TX300 Скачать руководство пользователя страница 73

Страница: 73 / 127

A26361-K881-Z102-4-7619

Preparation for Use and Operation

Configuring the Server

5.5.2

Configuration without ServerStart

Configuring HostRAID

The server is equipped with an onboard Ultra320 SCSI controller with HostRAID
functionality.

To configure HostRAID the controller has its own RAID-Select Utility. For
further information see “Adaptec HostRAID User’s Guide“ on the

Server-

Books

CD (choose

Controllers

from the menu).

Configuring the PCI RAID controller

If your server is fitted with a RAID controller, you must configure it as described
in the related documentation.

Configuring the onboard SCSI controller

You will find a description of the onboard SCSI controller configuration in the
Technical Manual for the system board (see “Related Publications” on
page 107). Further information is available on the driver diskettes provided.

Installing the operating system

Insert the installation floppy disk and the CD for the operating system you
want to install.

Reboot the server.

Follow the instructions on the screen and in the manual for the operating
system.

If your server is equipped with a RAID controller, please read how to install the
desired operating system in the related manual.

Содержание PRIMERGY TX300
































































































































Результаты поиска

Содержание PRIMERGY TX300

Отзывы:

Fujitsu PRIMERGY TX300, Руководство по эксплуатации, Страница: 73 / 127

Результаты поиска

Содержание PRIMERGY TX300

Отзывы: