Fujitsu PRIMERGY TX300 Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 127

Fujitsu PRIMERGY TX300 Скачать руководство пользователя страница 71

A26361-K881-Z102-4-7619

65

Preparation for Use and Operation

Starting up Hot-Plug PCI Slots

5.4

Starting up Hot-Plug PCI Slots

In addition to standard slots, the server also has hot-plug PCI slots. These hot-
plug PCI slots allow boards to be installed and removed during operation
assuming the operating system supports this functionality.

Every hot-plug PCI slot is assigned two indicators that signal the current status
of the slot. The indicators are visible on card guide on the inside of the server
((b) and (c) on figure 39 on page 95).

The possible indicator modes and their meaning are explained in table 3 on
page 62 and tab le 4 on page 63.

If it is attempted to remove the relevant board despite the illuminated green
indicator, the slot is automatically powered off to protect the board and the
system from any damage.

The hot-plug functionality is supported by the currently available Windows
operating systems.

The PCI hot-plug software (

PCI Card HotReplace)

is located on the

ServerStart

CD supplied or is installed with the

ServerView

agents. You will find additional

information on installation and operation in the file “README for the PCI Hot
Plug Software V3.0” on the

ServerStart

CD.

PCI components may only be installed and removed by personnel with the
appropriate technical training.

«
...
69
70
71
72
73
...
»

Содержание PRIMERGY TX300
































































































































Отзывы:

Нет отзывов