Fujitsu PRIMERGY TX300 Скачать руководство пользователя

Страница: 58 / 127

A26361-K881-Z102-4-7619

Connecting and Disconnecting Cables

Hardware Installation

4.7

Instructions on Connecting and
Disconnecting Cables

CAUTION!

Be sure to read the documentation for the peripheral devices before
connecting them.

Do not connect or disconnect data cables during a thunderstorm.

When removing a cable, always hold it by the plug. Never unplug a cable
by pulling at the cable itself.

Connect and disconnect the cables in the order described below.

Connecting cables

Turn off all power and equipment switches.

Pull all power plugs out of the grounded power sockets.

Plug all cables into the server and peripherals.

Plug all data communication cables into the utility sockets.

Plug all power cables into the grounded power sockets.

Disconnecting cables

Turn off all power and equipment switches.

Pull all power plugs out of the grounded power sockets.

Unplug all data communication cables from the utility sockets.

Disconnect the relevant cables from the server and all the peripherals.

Содержание PRIMERGY TX300
































































































































Результаты поиска

Содержание PRIMERGY TX300

Отзывы:

Похожие инструкции для PRIMERGY TX300

Бренды по названию

Популярные бренды

Fujitsu PRIMERGY TX300, Руководство по эксплуатации

Результаты поиска

Содержание PRIMERGY TX300

Отзывы:

Похожие инструкции для PRIMERGY TX300

Бренды по названию

Популярные бренды