Fujitsu PRIMERGY TX300 Скачать руководство пользователя | Manualshive

Страница: 35 / 127

background image

A26361-K881-Z102-4-7619

29

Hardware Installation

Installing/Removing the Rack Model into the Rack

4.4

Installing/Removing the Rack Model into
the Rack

V

CAUTION!

●

Please observe the safety notes and notes on mounting into the rack
in chapter “Important Notes” on page 13.

●

At least two people are needed to position the server into/out of the
rack.

●

The rack can tip over when more than one unit is pulled out.

●

The server may not occupy the top height unit of the rack (42 HU
Classic Rack, 38 HU/42 HU PRIMECENTER Rack and/or
DataCenter Rack), as otherwise no board and/or system fan can be
replaced even with the unit pulled out completely.

Requirements of the rack

The rack systems of the Fujitsu Siemens Computers GmbH (PRIMECENTER
Rack; DataCenter Rack and 19-Inch (Classic) Rack) support fully the instal-
lation of the PRIMERGY server systems. The installation into the at present
usual rack systems of different foreign manufacturers (3rd-Party Rack) is
supported to large part.

To accommodate the ventilation concept and ensure proper ventilation of the
components in the rack, any unused areas must be closed using dummy covers.

The power is supplied via the socket strips available in the rack.

The main features of the rack systems of the Fujitsu Siemens Computers are:

PRIMECENTER Rack

–

Frontally bolted telescopic rails or sliding rails.

The rails are provided with a linear alignment possibility to ensure also an
adjustment to different rack depths.

–

Extended cable management within the lateral rack area.

«
...
33
34
35
36
37
...
»

Содержание PRIMERGY TX300
































































































































Отзывы:

Нет отзывов

Похожие инструкции для PRIMERGY TX300

SBXL52 - Server Compute Blade

Бренд: Intel Страницы: 126

NPort W2150Plus Series

Бренд: Moxa Technologies Страницы: 167

Бренд: W&T Страницы: 228

Бренд: Ericsson Страницы: 159

PRIMERGY RX100 S7

Бренд: Fujitsu Страницы: 86

PRIMERGY RX1330 M1

Бренд: Fujitsu Страницы: 312

Primergy RX100 S4

Бренд: Fujitsu Страницы: 85

PRIMERGY RX1330 M1

Бренд: Fujitsu Страницы: 84

Primergy RX100 S3

Бренд: Fujitsu Страницы: 73

PRIMERGY RX100 S8

Бренд: Fujitsu Страницы: 82

PRIMERGY RX1330 M3

Бренд: Fujitsu Страницы: 342

PRIMERGY RX100 S7

Бренд: Fujitsu Страницы: 490

PRIMERGY RX1330 M3

Бренд: Fujitsu Страницы: 84

PCS400R Pro:Centric

Бренд: LG Страницы: 57

Бренд: LG Страницы: 104

Pro:Centric PCS200S

Бренд: LG Страницы: 40

Бренд: LG Страницы: 6

PCS500R Pro:Centric

Бренд: LG Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды