Fujitsu PRIMERGY TX2550 M5 Скачать руководство пользователя страница 71

Страница: 71 / 106

TX2550 M5

Operating Manual

Starting up

5.6

Switching on the server for the first time

CAUTION!

●

If nothing appears on the screen but flickering stripes after switching
on the server, switch off the server immediately (see chapter

"Troubleshooting and tips" on page 89

●

The On/Off button does not disconnect the server from the mains. To
completely disconnect it from the mains, remove the power cords
from the PSUs.

●

Do not move, strike, or shake the server when it is switched on. This
can damage the HDD/SSD in the server and cause data loss.

●

Switch the server on when the temperature is in the specified
temperature range. For more information on the operating
environment, see

"Ambient conditions" on page 101

. When operating

the server out of the specified temperature range, the server may
operate improperly and data loss may occur. Furthermore, Fujitsu
cannot be held responsible for any related damage, malfunction, or
loss of data, etc.

●

Ensure that you wait for 10 seconds or more after power off before
switching on the server again.

●

After connecting all power cords, wait at least 10 seconds before
pressing the On/Off button.

Switching the server on

The AC connected indicator lights up green (standby mode) when the server is
connected to the mains.

It will take about 60 seconds until the server can be switched on.

–

Starting up

For Japan, see "

はじめにお読みください

Press the On/Off button.

Configure your server and install the operating system, see section

"Configuring the server with ServerView Installation Manager" on
page 72

Содержание PRIMERGY TX2550 M5











































































































Результаты поиска

Содержание PRIMERGY TX2550 M5

Отзывы:

Похожие инструкции для PRIMERGY TX2550 M5

Бренды по названию

Популярные бренды

Fujitsu PRIMERGY TX2550 M5, Руководство по эксплуатации

Результаты поиска

Содержание PRIMERGY TX2550 M5

Отзывы:

Похожие инструкции для PRIMERGY TX2550 M5

Бренды по названию

Популярные бренды