Fujitsu PRIMERGY TX2550 M5 Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 106

background image

68

Operating Manual

TX2550 M5

Starting up

Information for ensuring electromagnetic compatibility

All data and signal cables must have sufficient shielding. The use of cable type
S/FTP Cat5 or higher is recommended.
Use of unshielded or badly shielded cables may lead to increased emission of
interference and/or reduced fault-tolerance of the device.

5.5.2

Connecting devices to the server

The connectors for external devices are on the front and rear of the server, see
section

"Connectors on the server" on page 27

I

For a remote installation using the ServerView Installation Manger a LAN
connection is necessary.

I

Some of the devices that can be connected may require special
software, e.g. drivers (see the documentation for the connected device).

Connecting the keyboard, mouse and monitor

Ê

Connect the keyboard and mouse to the USB connectors of the server.

Ê

Connect the monitor to one of the two video connectors at the front or rear.

I

The front video connector is designed for maintenance issues. If you
connect a monitor to the video connector at the front, the video
connector at the rear is deactivated. A monitor connected to the front
must have at least the same resolution as the monitor connected to
the rear. A console bypass is not possible via the video connector at
the front.

I

If a separate graphics card is installed in a slot, the graphic controller
on the system board is automatically deactivated. The corresponding
video connector can not be used. Connect the video cable of the
monitor to the video connector of the graphics card.

Ê

Connect the power cord of the monitor to a power outlet of the rack socket
strip.

I

The rated current for the monitor is indicated on the technical data label
on the monitor or in the operating manual for the monitor.

«
...
66
67
68
69
70
...
»

Содержание PRIMERGY TX2550 M5











































































































Отзывы:

Нет отзывов

Похожие инструкции для PRIMERGY TX2550 M5

Univerge SV8100

Бренд: NEC Страницы: 2

Бренд: Z Microsystems Страницы: 17

Бренд: Vxl Страницы: 19

Eserver 345 Series

Бренд: IBM Страницы: 70

Бренд: Pathos Acoustics Страницы: 26

xPort Pro XPP1004000-02R

Бренд: Lantronix Страницы: 17

Бренд: IBM Страницы: 70

Бренд: t.a.c. Страницы: 36

Бренд: ELStorage Страницы: 3

T19 Hydro Server

Бренд: BITMAIN Страницы: 17

Бренд: USR IOT Страницы: 48

NETWORK SATELLITE 5.3.0 - CHANNEL MANAGEMENT

Бренд: Red Hat Страницы: 318

AS2041M-32R Plus

Бренд: Supero Страницы: 106

34340 - StorCenter Pro ix4-100 NAS Server

Бренд: Iomega Страницы: 40

Бренд: D-Link Страницы: 12

Бренд: Gigabyte Страницы: 131

Бренд: ABLELink Страницы: 76

Бренд: Gigabyte Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды