Fujitsu PRIMERGY RX2530 M4 Скачать руководство пользователя страница 66

Страница: 66 / 88

Operating Manual

RX2530 M4

Starting up and operation

6.1.2

Server rear

6.1.2.1

Indicators on the I/O panel

ID, CSS and Global Error indicators

Figure 15: ID, CSS and Global Error indicators

Pos. Indicator

Status

Description

ID
indicator,
see also

blue on

The server has been highlighted using
ServerView Operations Manager, iRMC web
interface or the ID button on the front panel for
easy identification.

blue
flashing

The server has been highlighted for easy
identification using the iRMC (AVR) with
disabled local VGA output.

Global
Error
indicator,
see also

off

No critical event detected (non CSS
component).

orange
on

Prefailure event detected (non CSS
component).

orange
flashing

Non CSS component failure detected.
Possible causes:

– System is out of the specified range
– Defective sensor
– CPU error
– Error detected by server management

software

Содержание PRIMERGY RX2530 M4

























































































Результаты поиска

Содержание PRIMERGY RX2530 M4

Отзывы:

Бренды по названию

Популярные бренды

Fujitsu PRIMERGY RX2530 M4, Руководство по эксплуатации

Результаты поиска

Содержание PRIMERGY RX2530 M4

Отзывы:

Бренды по названию

Популярные бренды