Fujitsu PRIMEQUEST 440 Скачать руководство пользователя страница 104 | Manualshive

Страница: 104 / 280

Fujitsu PRIMEQUEST 440 Скачать руководство пользователя страница 104

3-6

C122-B001-02EN

CHAPTER 3 General Software Configuration

3.3.4

System data output tool (fjsnap)

fjsnap collects the system information (e.g., configuration information, operation
information, definition information, and logs) required for a failure investigation in
the event of a PRIMEQUEST system failure. This software can run in Linux.

3.4

Linked Software

This section describes optional software that can be used in linkage with the
PRIMEQUEST-series machines.

3.4.1

PRIMECLUSTER

PRIMECLUSTER is software for cluster operations. Install these programs as
necessary. Cluster operations can be performed between cabinets and between
partitions in a cabinet in the PRIMEQUEST system.

For details on cluster operations, see

CHAPTER 9, "Clustering."

For details on PRIMECLUSTER, see the PRIMECLUSTER manuals.

3.4.2

PRIMECLUSTER GDS

PRIMECLUSTER GDS is volume management software that helps increase the
availability of data stored in disk drive units and facilitates operation management of
the data. PRIMECLUSTER GDS protects disk data against hardware failures and
operating errors by users, and it provides assistance in operation management of disk
drive units.

For details on the redundant configuration, see

CHAPTER 6, "Redundant

Configuration."

For details on PRIMECLUSTER GDS, see the PRIMECLUSTER GDS manuals.

«
...
102
103
104
105
106
...
»

Содержание PRIMEQUEST 440

























































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды