Fujitsu PRIMEQUEST 1000 Series Скачать руководство пользователя страница 95

Страница: 95 / 344

4.3

RHEL Installation Procedures on the Built-in HDD

This section concisely describes the procedures for installing RHEL on the built-in HDD. Confirm the MMB

configuration and successful login to the MMB before starting the installation.

4.3.1

Advance setup

Set up the following as needed.

1. Remove each built-in HDD that is not the installation destination.

2. Confirm the partition settings of the PRIMEQUEST server with the MMB. For details, see

3.4 Configuring

a Partition

- Setting the SB/IOB/GSPB configuration

(See

3.4.1 Setting a partition configuration

- Configuring Console Redirection

(See

3.4.6 Configuring Console Redirection

- Video redirection: Enable

- Remote storage: Enable

- Console redirection: Enable

- Setting various modes

(See

3.4.5 Setting various modes

3. Assign I/O spaces to the SAS card, SAS array controller card, Onboard SAS controller (GSPB), SAS disk

unit controller and SAS array disk unit controller.

For details on I/O space assignment, see

3.4.5 Setting various modes

in this manual and 5.5.1 [Configure I/

O Space Assignment] menu in the

PRIMEQUEST 1000 Series Tool Reference

(C122-E110EN).

4.3.2

Preparing for Installation

No RHEL distribution DVD is available for RHEL installation. Users who have purchased a RHEL subscription

will need to create a RHEL distribution DVD.

Create an image of the RHEL distribution DVD.

Creating an image of the RHEL distribution DVD

https://access.redhat.com/

), download the image file of the distribution DVD

to another system.

Note

The image file of the distribution DVD varies with minor releases and the architecture (for x86/for Intel64).

Download the DVD image file appropriate to your needs.

Remarks

To download the file, you will need to register a subscription to Red Hat from Red Hat's customer portal.

Preparing for boot

1. Disconnect all the FC cables.

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 4 Installing the Operating System and Bundled Software

C122-E107-09EN

Содержание PRIMEQUEST 1000 Series

























































































































































































































































































































































Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Бренды по названию

Популярные бренды

Fujitsu PRIMEQUEST 1000 Series, Руководство по установке

Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Бренды по названию

Популярные бренды