Fujitsu PRIMEQUEST 1000 Series Скачать руководство пользователя страница 50

Страница: 50 / 344

Setting item

Value

Data bit

Parity

None

Stop bit

Flow control

None

Emulation

VT100

3.3.2

Initializing MMB settings

The procedure for initializing MMB settings is as follows.

If the field engineer has already made the settings, you can skip the following procedure.

Operations

1. Power on the main unit.

>> The Alarm LED of each unit goes on while the MMB Ready LED is blinking (initialization in progress).

The login prompt appears.

2. Log in with Administrator privileges using the terminal software from the MMB console PC.

>> When you first log in, you will be asked to change the Administrator password.

3. Set a password.

Note

You need to set a hard-to-guess password consisting of at least eight characters.

If you enter an inappropriate password, you will be asked to enter another password.

4. Configure the MMB network.

Execute the command shown below to set the IP address.

Administrator> set ip <IPAddress> <netmask>

Administrator> set gateway<default gateway IP Address>

Example: The IP address is 192.168.0.10, netmask is255.255.255.0, and gateway is 192.168.0.1.

Administrator> set ip 192.168.0.10 255.255.255.0

Administrator> set gateway 192.168.0.1

5. Execute the set http enable command to enable http.

>> The MMB Web-UI is accessible from the MMB console PC via the LAN.

Administrator> set http enable

Remarks

To enable https, use the set https command.

Administrator> set http enable

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 3 Work before Operating System Installation

C122-E107-09EN

Содержание PRIMEQUEST 1000 Series

























































































































































































































































































































































Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды

Fujitsu PRIMEQUEST 1000 Series, Руководство по установке

Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды