Fujitsu PRIMEQUEST 1000 Series Скачать руководство пользователя страница 299

Страница: 299 / 344

FIGURE E.5 Network configuration immediately after installation of OS

Remark

For details on each command used in the settings below, use man for confirmation.

Note

Do not set the host name before setting the IP address of vswif0, which exists by default immediately after the

installation of the operating system. If you do so, VMware 4.x may change the value of /etc/hosts to an unintended

value.

The description here is based on the assumption that vswif0 is used as the management LAN.

Confirming the PSA-to-MMB communication LAN and management LAN

1. The PSA-MMB communication LAN uses the physical adapter assigned BUS number 0000:00:19.0.

The management LAN uses an arbitrary physical adapter.

Execute the esxcfg-nics command to confirm the physical adapters used for the PSA-to-MMB

communication LAN and management LAN.

# esxcfg-nics -l

Name PCI Driver Link Speed Duplex\

MAC Address MTU Description

vmnic0 00:19.00 e1000e Up 100Mbps Half \

00:17:42:de:7c:4b 1500 \

Intel Corporation 82567LF-2 Gigabit Network Connection

vmnic1 0d:00.00 igb Up 100Mbps Full \

00:17:42:9b:dc:b4 1500 \

Intel Corporation 82576 Gigabit Network Connection

vmnic2 0d:00.01 igb Down 0Mbps Half \

00:17:42:9b:dc:b5 1500 \

Intel Corporation 82576 Gigabit Network Connection

PRIMEQUEST 1000 Series Installation Manual
APPENDIX E Notes on VMware Installation

271

C122-E107-09EN

Содержание PRIMEQUEST 1000 Series

























































































































































































































































































































































Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды

Fujitsu PRIMEQUEST 1000 Series, Руководство по установке

Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды