Fujitsu PRIMEQUEST 1000 Series Скачать руководство пользователя страница 253

Страница: 253 / 344

4. A confirmation dialog box appears. Click the [OK] button to continue processing or the [Cancel] button to

cancel processing.

Remarks

- If the power to the partition is already on or if thespecified control fails because the power is currently

off, a warning messageappears.

- If the power to all partitions is off, the partitions cannot be powered on for some time.

8.1.2

Powering off a partition

The procedure for powering off the partition is as follows.

In Windows, ServerView Agent is required to execute a shutdown from the MMB Web-UI.

For details on setting ServerView Agent, see the explanation regarding the [System Shutdown] tab in the

ServerView

Operations Manager Installation ServerView Agents for Windows.

If the following problems occur, check for details on the problem in 11.2.11 Problems with partition operations in

the

PRIMEQUEST 1000 Series Administration Manual

(C122-E108EN).

- The MMB Web-UI displays [Error] for [Status] (information area) because either of the following was

executed:

- [Power Off], [Reset], or [Force Power Off] of the partition

- Shutdown from the operating system

- The [MMB Web-UI] window displays "Read Error" for [Part Number] or [Serial Number] to indicate the

component status.

Operations

1. Log in to the MMB Web-UI.

The [MMB Web-UI] window appears.

2. Click [Partition] - [Power Control] from the MMB menu.

The [Power Control] window appears. The number in the [#] column is the partition number.

For details on the [Power Control] window, see 1.3.1 [Power Control] window in the

PRIMEQUEST 1000

Series Tool Reference

(C122-E110EN).

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 8 Powering On and Off a Partition

225

C122-E107-09EN

Содержание PRIMEQUEST 1000 Series

























































































































































































































































































































































Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды

Fujitsu PRIMEQUEST 1000 Series, Руководство по установке

Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды