Fujitsu PRIMEQUEST 1000 Series Скачать руководство пользователя страница 236

Страница: 236 / 344

FIGURE 7.2 Operation with external NTP servers (three NTP servers)

Only a single NTP server can be specified for a client. In this case, if the NTP client is no longer able to communicate

with the specified server, NTP server communication is lost because no other synchronized server is available.

Time correction via NTP is disabled during the time taken for recovery of communication between the NTP client

and NTP server. Time is measured based on system clock precision. Since system clock precision varies with the

system, in cases where the time is not corrected via NTP, middleware, or application problems may occur due to

an increasing time difference between systems.

Remarks

NTP servers 1 to 3 provide highly precise time over the Internet or intranet.

7.2.2

Setting an NTP server

Set another NTP server for time synchronization using the NTP client function of the MMB.

Note

The MMB time and the partition time are managedseparately by independent clocks.

The MMB clock does not report or adjust the partitiontime. Keep the MMB time and the partition time the same,

or at least close, becausethey are needed for the following cases:

- When checking the MMB log against the OS log in a partition at the hardware failure time

- When conducting a system audit or security audit

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 7 Work after Installation

208

C122-E107-09EN

Содержание PRIMEQUEST 1000 Series

























































































































































































































































































































































Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды

Fujitsu PRIMEQUEST 1000 Series, Руководство по установке

Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды