Fujitsu PRIMEQUEST 1000 Series Скачать руководство пользователя страница 234

Страница: 234 / 344

7.1

Duplicate Network Adapter Configuration

For the network configuration after installation, make teaming (multipath) settings as follows by using a utility

compatible with each network adapter.

Network adapter (Intel Gigabit Ethernet (GbE)) settings

Make the network redundancy settings for the management LAN and production LAN. The target networks are

shown in (2) in the following figure.

For Windows, configure teaming using Intel PROSet(R) (*1). For details, see the help for Intel PROSet(R).

*1 NIC teaming, a standard operating system function, is available in Windows Server 2012 or later.

No.

Description

(1)

SW redundancy

(2)

Redundancy by teaming (GLS or equivalent)

(3)

Disabled on the standby side

FIGURE 7.1 External network configuration

Note

There are some precautions on teaming with Intel PROSet(R). For details on the precautions, see APPENDIX G.

8 NIC (Network Interface Card) in the

PRIMEQUEST 1000 Series Administration Manual

(C122-E108EN).

PRIMEQUEST 1000 Series Installation Manual
CHAPTER 7 Work after Installation

206

C122-E107-09EN

Содержание PRIMEQUEST 1000 Series

























































































































































































































































































































































Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды

Fujitsu PRIMEQUEST 1000 Series, Руководство по установке

Результаты поиска

Содержание PRIMEQUEST 1000 Series

Отзывы:

Похожие инструкции для PRIMEQUEST 1000 Series

Бренды по названию

Популярные бренды