manualshive.com logo in svg

Fujitsu MB95630H Series, Руководство по оборудованию

Fujitsu MB95630H Series - это устройство с высокой производительностью, для которого доступен бесплатный Hardware Manual. Скачайте его с manualshive.com и узнайте все возможности этого продукта. Этот manual обеспечит вас всей необходимой информацией для эффективного использования. Не упустите шанс получить его прямо сейчас!

Поделиться
Скачать
background image

MB95630H Series

116

FUJITSU SEMICONDUCTOR LIMITED

MN702-00009-1v0-E

CHAPTER 9  WATCH PRESCALER
9.4  Operations and Setting Procedure 
Example

9.4

Operations and Setting Procedure Example

The watch prescaler operates as an interval timer.

■

Operations of Interval Timer Function (Watch Prescaler)

The counter of the watch prescaler continues to count down using the subclock divided by two

or the sub-CR clock divided by two as its count clock as long as the subclock or the sub-CR

clock oscillates.

When cleared (WPCR:WCLR = 1), the counter starts counting down from "0xFFFF". Once it

reaches "0x0000", it returns to "0xFFFF" to continue counting. As soon as the time set by the

interrupt interval time select bits has elapsed during the counting down, the watch prescaler

interrupt request flag bit (WPCR:WTIF) is set to "1" in any mode except the stop mode in

which the subclock mode or the sub-CR clock mode is used. In other words, a watch interrupt

request is generated at every selected interval time, based on the time when the counter was

last cleared.

■

Clearing Watch Prescaler

If the watch prescaler is cleared, other peripheral functions that are using the watch prescaler

output are affected by changes in count time and by other factors.

When clearing the counter using the watch prescaler clear bit (WPCR:WCLR), modify the

settings of other peripheral functions so that clearing the counter does not have any unexpected

effect on them.

When the output of the watch prescaler is selected as the count clock, clearing the watch

prescaler also clears the watchdog timer.

The watch prescaler is cleared not only by the watch prescaler clear bit (WPCR:WCLR) but

also when the subclock or the sub-CR clock is stopped and the oscillation stabilization wait

time is necessary. The watch prescaler is cleared in the following situations:

•

When the device transits from the subclock mode or sub-CR clock mode to the stop mode

•

When the subclock oscillation enable bit or the sub-CR clock oscillation enable bit in the
system clock control register 2 (SYCC2:SOSCE or SCRE) is set to "0" in main clock mode,
main CR clock mode, or main CR PLL clock mode.

In addition, the counter of the watch prescaler is cleared and stops operating when a reset is

generated.

■

Input Clock Selection for Watch Prescaler

Below are the clocks selected as input clocks of the watch prescaler in different clock modes.

•

In main clock mode, main CR clock mode, and main CR PLL clock mode

When the subclock oscillation is enabled and the subclock oscillation stabilization wait
time elapses, the subclock is selected as the input clock of the watch prescaler.

When the sub-CR clock oscillation is enabled and the sub-CR clock oscillation stabilization
wait time elapses, the sub-CR clock is selected as the input clock of the watch prescaler.

When the subclock oscillation and the sub-CR clock oscillation are enabled, and the
oscillation stabilization wait time elapses, the subclock is selected as the input clock of the
watch prescaler.

•

In subclock mode

Only the subclock is used as the input clock of the watch prescaler.

Содержание MB95630H Series





































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MB95630H Series

D-Link Express EtherNetwork DFE-670TXD Quick Install Manual preview
Express EtherNetwork DFE-670TXD
Бренд: D-Link Страницы: 4
DAD DSX 26 User Manual preview
DSX 26
Бренд: DAD Страницы: 36
D-Link DUB-1320 Quick Install Manual preview
DUB-1320
Бренд: D-Link Страницы: 2
CAME Z Series Manual preview
Z Series
Бренд: CAME Страницы: 4
dbx ProVocal Specifications preview
ProVocal
Бренд: dbx Страницы: 2
Zhone IMACS Network Device Product Manual preview
IMACS Network Device
Бренд: Zhone Страницы: 114
TDK HHM Series HHM2245SA1 Specifications preview
HHM Series HHM2245SA1
Бренд: TDK Страницы: 2
Renesas REJ06B0734-0100 Application Note preview
REJ06B0734-0100
Бренд: Renesas Страницы: 19
Renesas E200F User Manual preview
E200F
Бренд: Renesas Страницы: 76
Anthem Audio SFD-2 MkIII Jumper Configurations preview
SFD-2 MkIII Jumper
Бренд: Anthem Audio Страницы: 2
Renesas Protection Board R0E330850ACBP0 User Manual preview
Protection Board R0E330850ACBP0
Бренд: Renesas Страницы: 8
Intel G6950 Documentation Update preview
G6950
Бренд: Intel Страницы: 51
Mod Duo X User Manual preview
Duo X
Бренд: Mod Страницы: 11
Promise Technology Pegasus R4 Product Manual preview
Pegasus R4
Бренд: Promise Technology Страницы: 148
IBA FOB-SDexp Manual preview
FOB-SDexp
Бренд: IBA Страницы: 36
ADLINK Technology AMSTX-CF Series User Manual preview
AMSTX-CF Series
Бренд: ADLINK Technology Страницы: 73
YASKAWA CP 040 RS422/485 Manual preview
CP 040 RS422/485
Бренд: YASKAWA Страницы: 87
Juniper MX104 Quick Start Manual preview
MX104
Бренд: Juniper Страницы: 30

Бренды по названию

Популярные бренды

Загрузить еще бренды