manualshive.com logo in svg

Fujitsu MB90390 Series, Руководство по оборудованию

"Серия Fujitsu MB90390 - это инновационные микроконтроллеры, предназначенные для различных аппликаций. Получите бесплатное Hardware Manual для этой серии продуктов и узнайте все функции и возможности. Скачайте руководство с manualshive.com и начните использовать вашу технику на полную мощность."

Поделиться
Скачать
background image

519

CHAPTER 23  CAN CONTROLLER

23.16

Precautions when Using CAN Controller

Use of the CAN Controller requires the following cautions.

■

For -H Devices, e.q. MB90F394H and MB90V390H: Caution for Disabling Message 
Buffers by BVAL Bits

The use of BVAL bits may affect malfunction of CAN Controller when messages buffers are set disabled

while CAN Controller is participating in CAN communication (the read value of the CSR: HALT bit is "0"

and CAN Controller is ready to transmit messages). This section shows the work around of this

malfunction.

●

Condition

When following two conditions occur at the same time, the CAN Controller will not perform to transmit

messages normally.

•

CAN Controller is participating in the CAN communication. (i.e. The read value of the CSR: HALT bit

is" 0" and CAN Controller is ready to transmit messages)

•

Message buffers are read when BVAL bits disable the message buffers.

●

Work around

Operation for suppressing transmission request

Do not use BVAL bit for suppressing transmission request, use TCAN bit instead of it.

Operation for composing transmission message

For composing a transmission message, it is necessary to disable the message buffer by BVAL bit of

Message Buffer Valid Register to change contents of ID and IDE registers. In this case, BVAL bit

should reset (BVAL=0) after checking if TREQ bit is "0" or after completion of the previous message

transmission (TC=1).

In case a buffer needs to be disabled, ensure that no transmission request is pending (if it was requested

before). Therefore, do not reset BVALx-Bit before testing, if a transmission is ongoing:

a) Cancel the transmission request (TCANx=1;), if necessary

b) and wait for the transmission completion (while (TREQx=1);) by polling or interrupt.

Only after that the transmission buffer can be disabled (BVALx=0;).

Note for case a), if transmission of that buffer has already started, canceling the request is ignored and

disabling the buffer is delayed until the end of the transmission.

Содержание MB90390 Series





































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MB90390 Series

H3C WX5500H series User Configuration Manual preview
WX5500H series
Бренд: H3C Страницы: 57
Taie FA Series Operation Manual preview
FA Series
Бренд: Taie Страницы: 66
Walimex Pro Excellence Instruction Manual preview
Excellence
Бренд: Walimex Pro Страницы: 68
tams elektronik ABC-1 Manual preview
ABC-1
Бренд: tams elektronik Страницы: 12
Lamtec BT300 BurnerTronic Quick Reference preview
BT300 BurnerTronic
Бренд: Lamtec Страницы: 48
Unitech R16 Installer Manual preview
R16
Бренд: Unitech Страницы: 55
S&C 6802 Application Manual preview
6802
Бренд: S&C Страницы: 8
Fingertips Lab O6 Quick Start Manual preview
O6
Бренд: Fingertips Lab Страницы: 15
Newport MM4005 User Manual preview
MM4005
Бренд: Newport Страницы: 417
Desoutter 6159326760 Original Instructions Manual preview
6159326760
Бренд: Desoutter Страницы: 74
jablotron CL-301SL Quick Start Manual preview
CL-301SL
Бренд: jablotron Страницы: 2
Hattersley C31 Installation And Operating Instructions preview
C31
Бренд: Hattersley Страницы: 2
National Instruments PXIe-6595 Getting Started Manual preview
PXIe-6595
Бренд: National Instruments Страницы: 6
W.E.ST. SCU-138-P Technical Documentation Manual preview
SCU-138-P
Бренд: W.E.ST. Страницы: 34
Ltech TT-DX-R4-5A Manual preview
TT-DX-R4-5A
Бренд: Ltech Страницы: 4
Motor Guard M-60R Instructions preview
M-60R
Бренд: Motor Guard Страницы: 2
K&K M2700 Installation Instructions Manual preview
M2700
Бренд: K&K Страницы: 6
Ros IC-15X Operation And Maintenance Manual preview
IC-15X
Бренд: Ros Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды