Fujitsu IP Centrex SRS-12i Скачать руководство пользователя страница 18

Страница: 18 / 69

2-8

Fujitsu

IP Centr

ex T

elephone

Network Settings

VLAN Setting (Option 20)

The VLAN Setting is required in order to operate the telephone. To select
the VLAN Setting, follow the steps below:

1. Press OPTIONS, numeric key “2”, “0”, then ENTER.

2. Press ENTER.

3. Enter 8 digits of numeric password (see Administrator Password

Registration in chapter 4). Then ENTER.

* Factory Default Administrator Password - 99999999

4. LCD will display as below:

When you select 2: NO SUPPORT, and ENTER, the LCD will display as
below:

After this message is displayed the telephone will reset and the options
selected above will be implemented

When you select 1: SUPPORT, go to step 5 below.

5. Press 1: SUPPORT, then ENTER.

6. To overwrite, simply enter the new value between 2-4094. Then

ENTER.

VLAN SETTING
NON SUPPORTED

ENTER ADM PASSWORD

ENTER ADM PASSWORD
********

1: SUPPORT

2: NO SUPPORT
(SELECT 1-2)

NON SUPPORTED
COMPLETED

VLAN ID REGISTRATION
ID=2

(SELECT 2-4094)

VLAN ID REGISTRATION
ID=2000

(SELECT 2-4094)

Содержание IP Centrex SRS-12i






































































Результаты поиска

Содержание IP Centrex SRS-12i

Отзывы:

Похожие инструкции для IP Centrex SRS-12i

Бренды по названию

Популярные бренды

Fujitsu IP Centrex SRS-12i, Руководство администратора

Результаты поиска

Содержание IP Centrex SRS-12i

Отзывы:

Похожие инструкции для IP Centrex SRS-12i

Бренды по названию

Популярные бренды