Fujitsu General ASHG07KPCE Скачать руководство пользователя

Страница: 55 / 132

2-15. E: 94. Trip detection (Outdoor unit)

Indicator

Indoor unit

Operation indicator

9 time flash

Timer indicator

4 time flash

Economy indicator

Continuous flash

Error code

E: 94

Detective actuator

Outdoor unit

Main PCB

Protection stop by over-current generation after inverter
compressor start processing completed generated
consecutively 10 times.

NOTE:

The number of generations is reset when the
compressor starts up.

Compressor

Forecast of cause

Outdoor unit fan operation defective, foreign matter on

heat-exchanger, excessive rise of ambient temperature

Main PCB failure

Inverter compressor failure (lock, winding short)

Check point 1. Check the outdoor unit fan operation, heat-exchanger, ambient temperature

•

No obstructions in air passages?

•

Heat exchange fins clogged

•

Outdoor unit fan motor check

•

Ambient temperature not raised by the effect of other heat sources?

•

Discharged air not sucked in?

↓

Check point 2. Replace the main PCB

If Check point 1 do not improve the symptom, replace the main PCB.

↓

Check point 3. Replace compressor

If Check point 2 do not improve the symptom, change compressor.

↓

End

2-15. E: 94. Trip detection (Outdoor unit)

- (03-21) -

2. Troubleshooting with error code

TROUBLESHOOTING

Содержание General ASHG07KPCE





































































































































Результаты поиска

Содержание General ASHG07KPCE

Отзывы:

Похожие инструкции для General ASHG07KPCE

Бренды по названию

Популярные бренды

Fujitsu General ASHG07KPCE, Руководство по обслуживанию

Результаты поиска

Содержание General ASHG07KPCE

Отзывы:

Похожие инструкции для General ASHG07KPCE

Бренды по названию

Популярные бренды