manualshive.com logo in svg

Fujitsu Fujitsu fi-5950, Руководство оператора

Поделиться
Скачать
Fujitsu Fujitsu fi-5950 Скачать руководство пользователя страница 237

217

8.25 Timeout for Manual Feeding

8

SCANNER SETTINGS

8.25 Timeout for Manual Feeding

In manual feeding mode, if the scanner is left without loading the next document to scan for an extended 
time period, the scanner completes the scanning once and cancel the manual feeding mode. The time 
period is called “timeout”.

Configure the settings for the Timeout for Manual as follows:

1.

Start up the Software Operation Panel.

Refer to 

“8.1 Scanner Settings” on page 173

.

2.

Select [Device Setting 2] from left side list in the window, and select 
[Timeout for manual feeding] from its lower level.

3.

Select the timeout period for manual feeding.

You can specify the timeout period by seconds. Scanning will be complete when the specified 
time period has elapsed after the last sheet of paper was loaded onto the Hopper.

Select a timeout period from the following:
5, 10, 20, 30, 40, 50, 60, 70, 80, 90, 100, 110, 120, 180, 240, 300, 360, 420, 480, 540, 600, 900, 
1200, 1800, 1999 (seconds)

HINT

For details on how to scan the document manually, refer to 

“2.12 Feeding 

Documents Manually” on page 36

.

Содержание Fujitsu fi-5950


































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды