Fujitsu ETERNUS DX100 S3 Скачать руководство пользователя страница 88

Страница: 88 / 188

Check the setting completion message and click the [Done] button.
The screen display returns to the [Network] screen.

5.7

RAID Configuration Settings

Use ETERNUS Web GUI to set RAID configurations in the ETERNUS DX Disk storage system.
Perform the following settings:

•

RAID group creation

•

Volume creation

•

Hot spare registration

This section describes the configuration settings using a case of creating the following volumes as an exam-
ple.

•

Operation volume
Create an operation volume (Standard) in RAID5(4+1) RAID group.

•

Backup volume
Create a generation management volume (SDV) and temporary work volume (SDPV) in RAID5(2+1) RAID
group.

5.7.1

RAID Group Creation

Create RAID groups (groups of drives that configure RAID in the ETERNUS DX Disk storage system) to create
volumes.
Create an operation RAID group and a backup RAID group.

Figure 5.7 RAID Group Creation

RAID5 (4+1)

600GB

RAID5 (2+1)

2TB

Operation RAID group (RG0)

Backup RAID group (RG1)

Table 5.1 RAID Group Creation

Usage

Item

Create mode

RAID type

Configuration drive

Operation RAID
group (copy source)

RG0

Manual

RAID5

600GB SAS disk

Backup RAID group
(copy destination)

RG1

Manual

RAID5

2TB Nearline SAS
disk

Chapter 5 General Settings
5.7 RAID Configuration Settings

FUJITSU Storage ETERNUS DX100 S3/DX200 S3 Disk storage system Configuration Guide (Basic)

P3AM-7652-02ENZ0

Содержание ETERNUS DX100 S3




























































































































































































Результаты поиска

Содержание ETERNUS DX100 S3

Отзывы:

Fujitsu ETERNUS DX100 S3, Руководство по настройке, Страница: 88 / 188

Результаты поиска

Содержание ETERNUS DX100 S3

Отзывы: