Fujitsu ETERNUS DX S2, ETERNUS DX S3, ETERNUS DX S4, ETERNUS AF страница 11 Скачать руководство пользователя | Manualshive

Страница: 11 / 29

background image

Chapter 2 Notes
2.3 Server Notes

FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection-

Copyright 2018 FUJITSU LIMITED

P3AM-5672-10ENZ0

11

2.3

Server Notes

Before turning the server on, check that the ETERNUS DX/AF storage systems and Fibre Channel switches are
all "Ready". If the server is turned on and they are not "Ready", the server will not be able to recognize the
ETERNUS DX/AF storage systems.

Storage replication functions (local and remote) are performed by SHC-OSD (subsystem of BS2000) instead of
ETERNUS SF AdvancedCopy Manager.

SE Server (SU /390) and S-Server:

Before an online firmware update in the ETERNUS DX/AF storage system is performed, the timeout value for
the affected disks in the BS2000 must be increased to 2.5 minutes using the command /MODIFY-IO-UNIT. After
completion of the update, the standard timeout (1 minute) must be reset via /MODIFY-IO-UNIT.
For online firmware upgrades in 'operator intervention mode', additional conditions apply. Please respect
'important notices' and 'restrictions' in the storage bulletins.

«
...
9
10
11
12
13
...
»

Содержание ETERNUS DX S2, ETERNUS DX S3, ETERNUS DX S4, ETERNUS AF






























Отзывы:

Нет отзывов

Похожие инструкции для ETERNUS DX S2, ETERNUS DX S3, ETERNUS DX S4, ETERNUS AF

Бренд: G-Technology Страницы: 51

Q.HOME+ESS HYB-G2

Бренд: Qcells Страницы: 26

Бренд: Premio Страницы: 3

Бренд: QNAP Страницы: 69

RX343-S BLK/SLV

Бренд: Rosewill Страницы: 2

Бренд: NCR Страницы: 10

Бренд: kincrome Страницы: 2

Бренд: Olympus Страницы: 4

Бренд: Nexsan Страницы: 6

avigilon NVR4 Series

Бренд: Motorola solutions Страницы: 18

Feronia 00108066

Бренд: Hama Страницы: 8

Бренд: HOGYME Страницы: 31

Бренд: Cisco Страницы: 18

Бренд: Cisco Страницы: 8

Бренд: Cisco Страницы: 20

CSS8-IDM-MEM-HD

Бренд: Cisco Страницы: 4

Бренд: Cisco Страницы: 2

Memory Card MEMCUE-256D=

Бренд: Cisco Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды