1.5.3
emlxs.conf Parameter Example
A switch connection example is shown below.
# COPYRIGHT E004-2008 Emulex. All rights reserved.
# Solaris LightPulse emlxs driver: global initialized data.
#
# console-notices: Sets the verbose level for driver notices to the console.
# console-warnings: Sets the verbose level for driver warnings to the console.
# console-errors: Sets the verbose level for driver errors to the console.
#
# log-notices: Sets the verbose level for driver notices to the system log file*.
# log-warnings: Sets the verbose level for driver warnings to the system log file*.
# log-errors: Sets the verbose level for driver errors to the system log file*.
#
# *NOTE: The system log file is normally found at /var/adm/messages.
#
# Each parameter is a bit mask that enables/disables specific types of messages.
# If the bit is set, then the messages of that type are enabled.
#
# The available message types are listed below:
#
# LOG_MISC 0x00000001 /* Misc events */
# LOG_DRIVER 0x00000002 /* Driver attach and detach events */
# LOG_INIT 0x00000004 /* HBA initialization events */
# LOG_MEM 0x00000008 /* Memory management events */
# LOG_SLI 0x00000010 /* Service Level Interface (SLI) events */
# LOG_MBOX 0x00000020 /* Mailbox events */
# LOG_NODE 0x00000040 /* Node events */
# LOG_LINK 0x00000080 /* Link events */
# LOG_ELS 0x00000100 /* ELS events */
# LOG_PKT 0x00000200 /* General I/O packet events */
# LOG_FCP 0x00000400 /* FCP traffic events */
# LOG_TGTM 0x00000800 /* FCP target mode events */
# LOG_IP 0x00001000 /* IP traffic events */
# LOG_SFS 0x00002000 /* SFS events */
# LOG_IOCTL 0x00004000 /* IOCtl events */
# LOG_FIRMWARE 0x00008000 /* Firmware download events */
# LOG_CT 0x00010000 /* CT events */
# LOG_FCSP 0x00020000 /* FCSP events */
# LOG_RESERVED 0xfffc0000 /* Reserved for future use */
#
# Range: Min:0 Max:0xffffffff
#
# console-notices = 0; (Default)
# console-warnings = 0; (Default)
# console-errors = 0; (Default)
#
# log-notices = 0xffffffff; (Default)
# log-warnings = 0xffffffff; (Default)
# log-errors = 0xffffffff; (Default)
#
console-notices=0;
console-warnings=0;
console-errors=0;
log-notices=0xffffffff;
log-warnings=0xffffffff;
log-errors=0xffffffff;
# num-iocbs: Sets the number of iocb buffers to allocate.
#
# Range: Min:128 Max:10240 Default:1024
#
num-iocbs=1024;
# ub-bufs: Sets the number of unsolicited buffers to be allocated.
#
# Range: Min:40 Max:16320 Default:1000
#
ub-bufs=1000;
#
# +++ Variables relating to IP networking support. +++
#
# network-on: Enable/Disable IP networking support in the driver.
#
# 0 = Disables IP networking support in the driver.
# 1 = Enables IP networking support in the driver.
#
# Range: Min:0 Max:1 Default:1
#
network-on=1;
#
# +++ Fibre Channel specific para++
#
# topology: link topology for initializing the Fibre Channel connection.
#
Chapter 1 Operations When Using Oracle Fibre Channel Cards
1.5 Required Driver Parameters
23
FUJITSU Storage ETERNUS DX, ETERNUS AF Configuration Guide -Server Connection- (Fibre Channel) for Oracle Solaris
Copyright 2017 FUJITSU LIMITED
P3AM-6312-18ENZ0
Содержание ETERNUS DX Disk
Страница 2: ...This page is intentionally left blank ...
Страница 85: ......
