Fujitsu ESPRIMO E5635 Скачать руководство пользователя страница 81

Страница: 81 / 90

System

expansions

Fujitsu Technology Solutions

Extensions to the mainboard

The description of how to upgrade the main memory and/or processor is contained in the manual for
the mainboard.

►

Open the casing (see "Opening the casing").

►

Fold up the drive cage (see "Folding up the drive cage").

Upgrading main memory

►

Upgrade the memory according to the description in the manual for the mainboard.

►

Fold down the drive cage (see "Folding down the drive cage").

►

Close the casing (see "Closing the casing").

Replacing the processor

Before you can replace the processor, you need to folding up the ventilation duct (if equipped).

Folding up the ventilation duct

►

Grasp the ventilation duct from above and
fold it up.

►

Disconnect the power supply cable of the
processor fan from the mainboard (refer
to the manual for the mainboard).

►

Replace the processor as described in the
manual for the mainboard.

Содержание ESPRIMO E5635



























































































Результаты поиска

Содержание ESPRIMO E5635

Отзывы:

Похожие инструкции для ESPRIMO E5635

Бренды по названию

Популярные бренды

Fujitsu ESPRIMO E5635, Руководство по эксплуатации

Результаты поиска

Содержание ESPRIMO E5635

Отзывы:

Похожие инструкции для ESPRIMO E5635

Бренды по названию

Популярные бренды