manualshive.com logo in svg

Fujitsu ESPRIMO E5635, Руководство по эксплуатации

Поделиться
Скачать
Fujitsu ESPRIMO E5635 Скачать руководство пользователя страница 40

Troubleshooting and tips 

 

32 

Fujitsu Technology Solutions 

Power-on indicator remains unlit after you have 
switched on your device 

This may be due to the following: 

The mains voltage supply is faulty 

►

 

Check whether the power cable is plugged properly into the device and a grounded mains 
outlet. 

►

 

Switch the device on. 

Internal power supply overloaded 

►

 

Pull the power plug of the device out of the mains outlet. 

►

 

Wait for a moment. 

►

 

Plug the power plug into a properly grounded mains outlet again. 

►

 

Switch the device on. 

The device cannot be switched off with the ON/OFF 
switch 

Cause: The device has not been switched on with the ON/OFF switch. 

►

 

Press the ON/OFF switch again. 

Cause: System crash 

►

 

Press the ON/OFF switch for at least 4 seconds, until the device switches off. 

i

 

The operating system is not shut-down properly in the process. Error messages are 
therefore possible the next time the system is booted. 

The device cannot be switched on with the ON/OFF 
switch (0-Watt devices) 

The lithium battery is empty 

►

 

Press the emergency on button at the rear of the device, see chapter "Switching on a device 
when the lithium battery is discharged (0-Watt devices)". 

 

Содержание ESPRIMO E5635



























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды