Fujitsu eclipse Скачать руководство пользователя страница 74

Страница: 74 / 76

Glossary

Glossary-6 MDE-3893P Encore® and Eclipse® Series Owner’s Manual · December 2011

Seals

Substances used to prevent seepage of gasoline or vapor from the unit.

Serial Plate

Mounted on Side 1 of Encore units; mounted on left column of Eclipse units

Shear Valves

Device at the base of all dispensers and some pumps that shuts off the fuel flow in case of a
vehicle impact or fire at the base of the unit.

Silicone Grease

Type of lubricant used on the nozzle hooks and shafts of units.

Standalone Mode

Authorization and payout occur at the pump.

Submersible Turbine Pump (STP)

Submersible turbine pump in underground storage tank (UST).

Swivels

A fastening that permits the free turning of attached parts to the unit.

Two-wire Mode

A communication mode with the unit where authorization and payout occur at the console.

Vapor Hoses

Multi-wall hoses that reduces the amount of fuel vapor that escapes into the atmosphere when
a customer is dispensing fuel.

Vapor Recovery

Process of capturing emissions and returning them to an underground storage tank, reducing
the amount of volatile organic compounds emitted into the atmosphere.

Vapor Recovery Boots

Device inside the nozzle that reduces the amount of fuel vapor that escapes into the
atmosphere when a customer is dispensing fuel.

Содержание eclipse













































































Результаты поиска

Содержание eclipse

Отзывы:

Похожие инструкции для eclipse

Бренды по названию

Популярные бренды

Fujitsu eclipse, Руководство по эксплуатации

Результаты поиска

Содержание eclipse

Отзывы:

Похожие инструкции для eclipse

Бренды по названию

Популярные бренды