background image

6. Defrost operation control

Tn: Outdoor unit heat exchanger temperature
Ta: Outdoor temperature
Tn10: Temperature at 10 minutes after compressor start
Tnb: Temperature before 5 minutes

Triggering condition

The defrost operation starts when outdoor unit heat exchanger temperature sensor detects the
temperature lower than the values shown below.

1st time defrosting after starting operation

Compressor integrating

operation time

Less than 17 min.

17 to 57 min.

More than 57 min.

Condition

Does not operate

Tn ≤ -9°C and Tn-Ta ≥ 5

deg

Tn ≤ -5°C

2nd time and after

Compressor integrating

operation time

Less than 35 min.

More than 35 min.

Condition

Does not operate

Tn-Tn10 < -5 deg (Tn ≤ -10°C)

Tn-Tnb < -2 deg (Tn ≤ -10°C)

Tn ≤ -25°C (Ta ≥ -20°C)

Tn ≤ Ta-7°C or Tn ≤ -25°C (Ta < -20°C)

Integrating defrost (Constant monitoring)

Compressor integrating

operation time

More than 240 min. (For

long continuous

operation)

More than 215 min. (For

long continuous

operation

Less than 10 min.* (For

intermittent operation)

Condition

Tn ≤ -3°C

Tn ≤ -5°C

Count of the compressor

off: 40 times

*: If the compressor continuous operation time is less than 10 minutes, the number of the com-
pressor off is counted. If any defrost operated, the compressor off count is cleared.

Release condition

The defrost operation is released when either one of the conditions below is satisfied.

Outdoor unit heat exchanger temperature
(after 1 minute or later since compressor start)

12°C or more

Compressor operation time

15 minutes

- (04-25) -

6. Defrost operation control

CONTROL AND

FUNCTIONS

CONTROL AND

FUNCTIONS

Содержание AUXG36KRLB










































































































































































Отзывы: