Fujitsu AOUG09LZAS1 Скачать руководство пользователя | Manualshive

Страница: 125 / 179

background image

2. Auto changeover operation

When the air conditioner is set to AUTO mode by remote controller, operation starts in the optimum
mode from among heating, cooling, dry and monitoring modes. During operation, the optimum mode
is automatically switched in accordance with temperature changes. The temperature can be set be-
tween 64.4°F (18°C) and 86.0°F (30°C) in 1.8°F (1.0°C) steps.

• When operation starts, indoor fan and outdoor fan are operated for around 1 minute.

Room temperature and outdoor temperature are sensed, and the operation mode is selected in
accordance with the table below.

Room temperature

Operation mode

Tr > Ts + 3.6°F (2°C)

Cooling

Ts + 3.6°F (2°C) ≥ Tr ≥ Ts - 3.6°F (2°C)

Middle zone

Tr < Ts - 3.6°F (2°C)

Heating

Tr: Room temperature
Ts: Setting temperature

NOTE:

When the operation mode is middle zone, indoor unit operation mode is selected as below.

• Same operation mode is selected as outdoor unit.

If outdoor unit is operating in cooling and heating mode, indoor unit will be operated by
the same operation mode.

• Selected by outdoor temperature.

If outdoor unit is operating in other than cooling and heating mode, indoor unit will be op-
erated according to the outdoor temperature as below.

Outdoor temp.

Operation mode

77.0°F (25°C) or more

Cooling

Less than 77.0°F (25°C)

Heating

• When the compressor was stopped for 6 consecutive minutes by temperature control function af-

ter the cooling or heating mode was selected as above, operation is switched to monitoring mode
and the operation mode selection is done again.

• When the middle zone is selected on the predetermining of the operation mode, the operation

mode before the changing to the monitoring mode is selected.

- (04-7) -

2. Auto changeover operation

CONTROL AND

FUNCTIONS

CONTROL AND

FUNCTIONS

«
...
123
124
125
126
127
...
»

Содержание AOUG09LZAS1




















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AOUG09LZAS1

Бренд: iGenix Страницы: 9

Бренд: Hamilton Beach Страницы: 48

Бренд: Daitsu Страницы: 21

Бренд: Midea Страницы: 36

MTA8F128R5I Series

Бренд: Technibel Climatisation Страницы: 47

Бренд: Daikin Страницы: 18

Бренд: Hisense Страницы: 31

Бренд: TECO Страницы: 24

Бренд: asecos Страницы: 52

Бренд: German pool Страницы: 44

GRF128R5I Series

Бренд: Technibel Climatisation Страницы: 40

DO-CH-ACL150DRT

Бренд: Dutch originals Страницы: 48

Бренд: DayRelax Страницы: 100

Бренд: dirna Bergstrom Страницы: 84

Бренд: ozone generators Страницы: 13

Бренд: Sonnenkonig Страницы: 36

Бренд: Airtok Страницы: 14

AIR COOLED CONDENSING UNIT 38EH

Бренд: Carrier Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды