FUJIPLA AL-MEISTER ALM3230 Скачать руководство пользователя

Страница: 48 / 68

DryLam

A Trademark of Martin Yale Industries

251 Wedcor Avenue, Wabash, IN 46992

Brian Jennett- Tech-Line & Service Advisor/Manager

Phone: (260-569-7231)

www.DryLam.com

ALM3230 Customer Instruction Manual.docx

Page 48 of 68

5. AUTOMATIC OPERATION (cont’d)

5-2-7. CUT ADJUST

This function adjusts the cutting positions at both the leading, and trailing edges of the paper.

NOTE: These settings are retained in memory after a power outage.

NOTE: These settings only affect the leading and trailing edge cuts. They do not affect the side cuts

made by the Trimmer Unit.

NOTE: It is recommended to read and record the present values shown on the display before adjusting.

It may be helpful if it is necessary to set back to a past value.

NOTE: Each ALM3230 has its own Cut Adjust values. The numbers seen are relative only to this

particular machine and not to anything in the “real world”.

1. Select Cut Adjust from the Mode display.

---- CUT ADJUST ----

>F: 0.012inch

B:-0.004inch

2. Press TEMP/SPEED button to toggle between F and B.

F: cutting position at the front end (leading edge)

B: cutting position at the back end (trailing edge)

Do nothing to return to the operation screen.

3. Or, set one or both values using the UP/Down buttons.

On version 1 adjustment can be done between:

F and B: TBD

Do nothing to retain the settings and return to the operation menu.

Содержание AL-MEISTER ALM3230





































































Результаты поиска

Содержание AL-MEISTER ALM3230

Отзывы:

Похожие инструкции для AL-MEISTER ALM3230

Бренды по названию

Популярные бренды

FUJIPLA AL-MEISTER ALM3230, Инструкция по эксплуатации

Результаты поиска

Содержание AL-MEISTER ALM3230

Отзывы:

Похожие инструкции для AL-MEISTER ALM3230

Бренды по названию

Популярные бренды