Nut
Conduit
Conduit
(Not supplied)
Nut
(Not supplied)
Before installation and operation, read these instructions carefully
and use this product only in the manner described by the
manufacturer in the operation manual.
The instruction shown below are used to alert you to potential
personal injury and property damage hazards.
There are three hazard classifications based on potentially
dangerous situations.
Obey all safety instructions that show these symbols to avoid
possible injury, death and property damage.
SAFETY INSTRUCTIONS
WARNING:
WARNING indicates a potentially
hazardous situation which, if not
avoided, could result in death or
serious injury.
CAUTION:
CAUTION indicates a potentially
hazardous situation which, if not
avoided, may result in minor or
moderate injury.
NOTE
: The safety instructions are explained with the following
pictographic symbols.
means forcible execution. It indicates actions, if
any, that must be done.
WARNING
1. TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
a) Use this unit only in the manner intended by the
manufacturer. If you have questions, contact the
manufacturer.
b) Before servicing or cleaning unit, switch power
off at service panel and lock the service
disconnecting means to prevent power from being
switched on accidentally. When the service
disconnecting means cannot be locked, securely
fasten a prominent warning device, such as a tag,
to the service panel.
CAUTION
INSTALLATION
1. Preparation
2. Range Hood Mounting
3
Check that the top of the ex-
haust port is inserted into the
bottom of 10" round duct, then
make the duct joint secure and
air tight using non-flammable
tape such as duct tape, etc.
(not supplied)
3. Connecting Power Supply Wires
1
Remove the nut from the conduit
connector at the end of power wiring.
2
R e m o v e t w o
screws fixing
the wire cover
and detach it.
4. Final Assembly and Check
3. Read specification label on this product for further
information and requirements.
2. To reduce the risk of fire and to properly exhaust
air, be sure to duct air outside. Do not vent exhaust
air into spaces within walls or ceilings or into attics,
crawl spaces, or garages.
6. Fasten the filter and other parts securely. Incorrect
attachment may result in personal injury or property
damage.
4. Use only for the purpose of kitchen ventilation.
1. For general ventilating use only. Do not use to
exhaust hazardous or explosive material and
vapors.
5. Do not install this range hood in the bathroom or in
other wet rooms since electrical shock and damage
may result.
2. To reduce the risk of fire or electric shock, do not
use this product with any solid-state speed control
device.
4. TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS, OBSERVE
THE FOLLOWING:
a) Installation work and electrical wiring must be done
by a qualified person(s) in accordance with all
applicable codes and standards, including fire-rated
construction.
b) Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) of
fuel burning equipment to prevent back drafting.
Follow the heating equipment manufacturer’s
guidelines and safety standards such as those
published by the National Fire Protection
Association (NFPA), and The American Society for
Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE), and the local code
authorities.
c) When cutting or drilling into wall or ceiling, do not
damage electrical wiring and other hidden utilities.
d) Ducted fans must always be vented to the outdoors.
e) The end user is responsible to ensure compliance
with all Federal, State and Local Environmental and
Fire codes.
1
According to the conditions where the range hood is installed, de-
termine whether it will be discharged vertically or horizontally (10"
Round duct). For vertical or horizontal discharge, run duct work be-
tween the hood location and the exterior blower used with the range
hood. For best result in either direction, use a minimum number of
transitions and elbows. As for installing the exterior blower, please
refer to its installation.
2
The range hood unit must be mounted to a liner which has the
following dimensions. Install the liner securely after checking that
the opening size of the liner is the same as the figure below.
• If the range hood is not installed properly, it could become detached
and fall.
• Ensure that the metal duct does not touch other metal housing
materials, otherwise fire or electric shock could result.
• When the liner is installed in the wooden hood, the inside of the
wooden hood placed above the cooking surface must be fully covered
by the metal barrier including bottom edges. Select a suitable liner
and metal barrier according to the size and shape of the wooden
hood and install properly.
• The liner should be installed tightly. If the liner installation is not correct,
the range hood unit may become detached and fall.
• Wear working gloves to avoid injury.
• To prevent air or moisture from entering through the wall opening,
be sure to install wall insulation to seal around duct work completely.
CAUTION:
5. Explanation to the End User
(1) Referring to the Operation Manual, explain the operation of this
range hood to end users.
(2) The Installation Manual and Operation Manual should be given to
the end user.
1
Assembly
1) Remove the switch’s protective cardboard.
2
Check
(1) Turn on the electrical circuit
to the range hood.
(2) Make sure that the switch
and light operate correctly.
Refer to page 5 of the
Operation Manual.
(3) Make sure that the range
hood functions rightly and it
has no abnormal noises
and/or vibration.
• Electrical wiring should be done by a qualified person(s) in
accordance with all applicable codes and standards, including
fire-rated construction. An unqualified person doing the work could
result in fire, electric shock or injury.
• This range hood uses 120V AC. Do not connect to other voltage
since fire, electric shock or damage could result.
Be sure to switch power OFF at
service panel before wiring.
3
Connect the conduit through
the connecting hole of the
body using the nut previously
removed.
4
Connect the electrical
wires as follows:
• Black to Black
• White to White
• Green to Green
Connect wires tightly
and securely using
wire connectors
(not supplied).
5
Replace the wire
cover with the screws
removed previously.
Make sure that all
wires are connected
properly and enclosed
inside of the wiring
compartment.
2
Hold up the range hood and align the 4 screw holes of the liner and
range hood, then fix securely using the supplied screws (M5
×
30)
and nuts.
Note:
Fasten all the screws and nuts evenly.
CAUTION:
CAUTION used without the safety
alert symbol indicates a potentially
hazardous situation which, if not
avoided, may result in property
damage.
means prohibition. It indicates actions, if any, that
mustn’t be done.
5. TO REDUCE THE RISK OF FIRE, USE ONLY
METAL DUCTWORK.
6. This unit must be grounded.
CIRCUIT DIAGRAM
7. Install this range hood to a liner. Check that the
hood is correctly installed, since incorrect
installation could result in the range hood becoming
detached and falling off.
8. Connect only to an AC120 Volt power source or
the range hood could result in fire, electric shock,
and damage.
SIZE & DIMENSIONS
CAUTION:
WARNING:
WARNING:
WARNING:
Liner Dimensions
!Æ! " # $
1
Detach the filters by loosening 2 screws. Then remove 5 screws
fixing the front cover and detach the front cover.
Cardboard
(Do not remove yet.)
Front cover
Screw
Filter
Loosen 2 screws
to remove the filter.
Non-flammable tape
Liner
Screw-washer
[Right & left, each
two (2) places]
[Securing plate turns
while passing through
the opening of Liner]
Securing plate
Four screws (M5
×
30)
Liner
Wire cover
Screw
Wire Connector
(Not supplied)
Wire cover
Screw
Cardboard
Filter
Front cover
Screw
Bulb
(Not supplied)
Push to turn ON
* As for operating the exterior blower used with this hood, please
refer to its operation manual.
9-13/16"
23-3/8"
25-1/16"
14-1/8"
15-13/16"
6-3/4"
9/16"
26"
9-13/16"
4-3/4"
9/16"
1"
16-7/8"
3-9/16"
4-Ø1/4"
Holes for mounting range hood
Ø7/8"
Ø9-15/16"
27"
(Unit: inch)
NAMES OF PARTS
Filter
Lamp Switch
ON
OFF
Lamp
(Not supplied)
Lamp
(Not supplied)
Front Cover
Enclosure
Connector
Connector
Connector
Connector
Terminal
Terminal
White
White
White
Green
Black
White
Black
Black
White
White
Black
Black
White
Black
Black
120V 60Hz
Lamp:50W
Lamp:50W
Switch (Lamp)
RANGE HOOD LOCATION
1
The range hood must be in-
stalled just above the cooktop.
2
The minimum distance from the
cooking surface to the bottom
of the range hood must be 24".
3
The total weight of the BUF-06E
range hood unit is 11 lbs. (5 kg)
4
Power requirements are:
AC120 V, 60 Hz, 1.0 Amp
• To protect hands from injury, wear working gloves when
installing the range hood.
CAUTION:
24" (Minimum)
Cook top
Liner
ACCESSORIES
Screw M5
×
30
Four (4) pieces
Nut with plate
Four (4) pieces
3) Two 50 Watt halogen light bulbs (not supplied) can be mounted
in this range hood.
Prior to function check, install light bulbs (PAR20 bulb, with
base diameter 26 mm: medium base), rated 120 V - 50 Watt or
below.
The following light bulbs are recommended for this range hood.
• GE Model No. 50PAR20H/FL25
• SYLVANIA Model No. 50PAR20/HAL/DL/NFL
Turn the lamps clock-wise to install them.
3. Do not attempt to control Remote Blower using
the internal switch provided on the front panel of
the BUF-06E.
THIS SWITCH IS TO BE USED FOR THE
CONTROL OF THE LIGHTS ONLY! A SEPARATE
S W I T C H , W I T H P R O P E R LY R AT E D
A M P E R A G E M U S T B E I N S TA L L E D TO
CONTROL THE REMOTE BLOWER MOTOR.
Contact the Remote Blower manufacturer or a
Certified Electrician for their recommendations.
8. To reduce the risk of fire and electric shock, install
this range hood only with remote blower models
rated maximum current of 12.8 amps.
INSTALLATION MANUAL
Model: BUF-06E
1U03 1182
Range Hood
7. Keep your hands and other objects away from the
fan while it is in motion. The range hood may injure
you or damage itself.
Do not remove the switch’s protective cardboard until proceeding to
“4. Final Assembly and Check”.
CAUTION:
2) Attach the front cover, and secure it with 5 screws.
Then attach the filters.
Remove the protective cardboard without fail, otherwise there is
a risk of fire.
WARNING:
• Check that the hood is correctly installed, since incorrect
installation could result in the detachment of the range hood
and the unit could fall.
WARNING:
• The liner shape illustrated in this installation manual is only for
reference.
CAUTION:
