manualshive.com logo in svg

FujiFilm FinePix S1500, Руководство по обслуживанию, Страница: 91 / 142

Поделиться
Скачать
FujiFilm FinePix S1500 Скачать руководство пользователя страница 91

FinePix S1500 Service Manual

4-33

4. Adjustments

Confidential: FUJIFILM Service Center Use Only

Lens Holder

Lens Base Plate

Lens Stand

Attention when conversion lens is used.
Convex side : Subject side.
Plane : Camera lens side.

Washer
(Plastic)

Fixed Ring

4-14.  AF Adjustment

<Settings for AF Adjustment>

(1) Set up the EFA chart and conversion lens so that they are 500 ± 5 mm apart.
(2) Position the chart so that the brightness of the chart surface is between 1000 ± 200 LUX.
(3) Position the 500 mm conversion lens 25 ± 2 mm from the front end of the lens.

<EFA chart>

EFA chart

Fluorescent 
light stand

Center

500mm conversion lens

500 ± 5 mm

Camera

25±2 mm with the zoom set to wide. 
Note that the camera lens should not touch 
the conversion lens.

<Step 1>

Insert the adjustment SD card into the camera, set the Mode dial to "

q

" and then turn the camera on.

<Step 2>

When the screen shown on the right appears, press the 
Down button to change to "3".

Содержание FinePix S1500















































































































































Отзывы:

Нет отзывов